首頁產品展示>珀金斯Perkins1204E-1206E故障排除（英文）

珀金斯Perkins1204E-1206E故障排除（英文）

珀金斯Perkins1204E-1206E故障排除，珀金斯Perkins1204E-1206E故障排除技術支持中心，珀金斯Perkins1204E-1206E故障排除代理商，珀金斯Perkins1204E-1206E故障排除銷售服務中心，珀金斯Perkins1204E-1206E故障排除價格規格資料查詢，寧波日昕動力科技有限公司

產品咨詢

Troubleshooting

1204E-E44TA, 1204E-E44TTA and

1206E-E66TA Industrial Engines

BK1 (Engine)

MK1 (Engine)

ML1 (Engine)

This document is printed from SPI². Not for RESALE

Important Safety Information

Most accidents tha t involve produc t op eration, ma intena nc e and repair are caus ed by failure to

ob serve basic safety rules or precautions . An accident can often be avoided by recog nizing pote ntially

ha za rdous situations before an accident oc curs . A person mus t be alert to pote ntial ha za rds. This

person should also ha ve the ne cessary training, skills and tools to perform the se func tions properly.

Improper operation, lubrication, maintenance or repair of this product can be dangerous and

could result in injury or death.

Do not operate or perform any lubrication, maintenance or repair on this product, until you have

read and understood the operation, lubrication, maintenance and repair information.

Sa fety precautions and warning s are provided in this ma nua l and on the produc t. If the se ha za rd

warning s are not he eded, bod ily injury or death could oc cur to you or to othe r persons .

The ha za rds are identified by the “Safety Alert Symb ol” and followed by a “Signa l Word” suc h as

“DANGER”, “WARNING” or “CAUTION”. The Sa fety Alert “WARNING” label is shown below.

The me aning of this safety alert symb ol is as follows:

Attention! Become Alert! Your Safety is Involved.

The me ssage tha t appears und er the warning explains the ha za rd and can be either written or

pictorially presente d.

Op erations tha t ma y caus e produc t dama ge are identified by “NOTICE” labels on the produc t and in

this pub lication.

Perkins cannot anticipate every possible circumstance that might involve a potential hazard. The

warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure,

work method or operating technique that is not specifically recommended by Perkins is used,

you must satisfy yourself that it is safe for you and for others. You should also ensure that the

product will not be damaged or be made unsafe by the operation, lubrication, maintenance or

repair procedures that you choose.

The informa tion, specifications , and illustrations in this pub lication are on the basis of informa tion tha t

was available at the time tha t the pub lication was written. The specifications , torque s, pressure s,

me asure me nts , adjustme nts , illustrations , and othe r items can cha ng e at any time. These cha ng es can

affect the service tha t is given to the produc t. Ob tain the comp lete and mos t current informa tion before

you start any job. Pe rkins dealers or Pe rkins distributors ha ve the mos t current informa tion available.

When replacement parts are required for this

product Perkins recommends using Perkins

replacement parts.

Failure to heed this warning can lead to prema-

ture failures, product damage, personal injury or

death.

This document is printed from SPI². Not for RESALE

KENR9116-01

3

Table of Contents

Table of Contents

Engine Stalls at Low RPM .................................... 94

Engine Top Speed Is Not Obtained ...................... 96

Engine Vibration Is Excessive ............................ 101

Exhaust Has Excessive Black Smoke ................ 102

Exhaust Has Excessive White Smoke ................ 104

Fuel Consumption Is Excessive .......................... 106

Fuel Contains Water ........................................... 108

Fuel Rail Pressure Problem ................................ 109

Fuel Temperature Is High .................................... 117

Inlet Air Is Restricted ............................................ 119

Inlet Air Temperature Is High .............................. 120

Intake Manifold Air Pressure Is High .................. 121

Intake Manifold Air Pressure Is Low ................... 122

Intake Manifold Air Temperature Is High ............. 123

NRS Exhaust Gas Temperature Is High ............ 124

NRS Mass Flow Rate Problem ........................... 127

Oil Consumption Is Excessive ............................ 130

Oil Contains Coolant ........................................... 132

Oil Contains Fuel ................................................ 133

Oil Pressure Is Low ............................................. 134

Power Is Intermittently Low or Power Cutout Is

Troubleshooting Section

Electronic Troubleshooting

Welding Precaution ................................................. 5

System Overview .................................................... 5

Glossary ................................................................ 12

Electronic Service Tools ........................................ 16

Indicator Lamps .................................................... 18

Replacing the ECM ............................................... 21

Self-Diagnostics .................................................... 22

Sensors and Electrical Connectors ....................... 22

Engine Wiring Information .................................... 31

ECM Harness Connector Terminals ..................... 36

Programming Parameters

Programming Parameters ..................................... 37

Test ECM Mode .................................................... 37

Factory Passwords ............................................... 37

Flash Programming .............................................. 38

Injector Code - Calibrate ....................................... 39

Mode Switch Setup ............................................... 40

Throttle Setup ....................................................... 41

Multiposition Switch Setup .................................... 44

Intermittent ........................................................ 136

Valve Lash Is Excessive ..................................... 141

Troubleshooting with a Diagnostic Code

Diagnostic Trouble Codes ................................... 142

Diagnostic Code Cross Reference ..................... 147

No Diagnostic Codes Detected ........................... 151

Customer Speciﬁed Parameters

Customer Speciﬁed Parameters ........................... 45

Customer Speciﬁed Parameters Table ................. 51

Customer Speciﬁed Parameters Worksheet ......... 54

Troubleshooting with an Event Code

Event Codes ...................................................... 152

Diagnostic Functional Tests

System Conﬁguration Parameters

System Conﬁguration Parameters ........................ 58

5 Volt Sensor Supply Circuit - Test ..................... 154

Analog Throttle Position Sensor Circuit - Test .... 163

CAN Data Link Circuit - Test ............................... 168

Data Link Circuit - Test ........................................ 172

Diesel Particulate Filter Identiﬁcation Signal -

Symptom Troubleshooting

Acceleration Is Poor or Throttle Response Is

Poor .................................................................... 60

Alternator Is Noisy ................................................ 66

Alternator Problem ................................................ 66

Battery Problem .................................................... 66

Coolant Contains Oil ............................................. 67

Coolant Level Is Low ............................................ 67

Coolant Temperature Is High ................................ 68

Crankcase Breather Ejects Oil .............................. 71

Crankcase Fumes Disposal Tube Has Oil

Draining ............................................................... 72

Cylinder Is Noisy ................................................... 73

Diesel Particulate Filter Collects Excessive Soot .. 74

Diesel Particulate Filter Temperature Is Low ........ 75

ECM Does Not Communicate with Other

Modules .............................................................. 76

ECM Will Not Accept Factory Passwords ............. 76

Electronic Service Tool Does Not Communicate .. 77

Engine Cranks but Does Not Start ........................ 78

Engine Does Not Crank ........................................ 84

Engine Has Early Wear ........................................ 85

Engine Has Mechanical Noise (Knock) ................ 85

Engine Misﬁres, Runs Rough or Is Unstable ........ 86

Engine Overspeeds .............................................. 91

Engine Shutdown Occurs Intermittently ............... 92

Engine Speed Does Not Change .......................... 93

Test ................................................................... 179

Digital Throttle Position Sensor Circuit - Test ..... 183

ECM Memory - Test ............................................ 192

Electrical Connectors - Inspect ........................... 193

Engine Pressure Sensor Open or Short Circuit -

Test ................................................................... 197

Engine Speed/Timing Sensor Circuit - Test ........ 204

Engine Temperature Sensor Open or Short Circuit -

Test ................................................................... 212

Engine Temperature Sensor Open or Short Circuit -

Test ................................................................... 217

Ether Starting Aid - Test ...................................... 224

Fuel Pump Relay Circuit - Test ........................... 228

Glow Plug Starting Aid - Test .............................. 236

Idle Validation Switch Circuit - Test ..................... 242

Ignition Keyswitch Circuit and Battery Supply Circuit -

Test ................................................................... 248

Indicator Lamp Circuit - Test ............................... 255

Injector Data Incorrect - Test ............................... 258

Injector Solenoid Circuit - Test ............................ 260

Mode Selection Circuit - Test .............................. 267

Motorized Valve - Test ........................................ 271

PTO Switch Circuit - Test .................................... 276

Sensor Calibration Required - Test ..................... 279

Solenoid Valve - Test .......................................... 282

This document is printed from SPI². Not for RESALE

4

KENR9116-01

Table of Contents

Soot Sensor - Test .............................................. 288

Throttle Switch Circuit - Test ............................... 291

Valve Position Sensor - Test ............................... 295

Water In Fuel Sensor - Test ................................ 301

Index Section

Index ................................................................... 306

This document is printed from SPI². Not for RESALE

KENR9116-01

5

Troubleshooting Section

Troubleshooting Section

Electronic Troubleshooting

i04029202

Welding Precaution

Correct welding procedures are necessary in order to

avoid damage to the following components:

• Electronic Control Module (ECM) on the engine

• Clean Emissions Module (CEM)

• Sensors

g01143634

Illustration 1

• Associated components

Service welding guide (typical diagram)

Components for the driven equipment should also be

considered. When possible, remove the component

that requires welding. When welding on an engine

that is equipped with an ECM and removal of the

component is not possible, the following procedure

must be followed. This procedure minimizes the risk

to the electronic components.

5. When possible, connect the ground clamp for

the welding equipment directly to the engine

component that will be welded. Place the clamp

as close as possible to the weld. Close positioning

reduces the risk of welding current damage to the

engine bearings, to the electrical components,

and to other components.

1. Stop the engine. Remove the electrical power

from the ECM.

6. Protect the wiring harnesses from welding debris

and/or from welding spatter.

2. Ensure that the fuel supply to the engine is turned

off.

7. Use standard welding procedures to weld the

materials together.

3. Disconnect the negative battery cable from the

battery. If a battery disconnect switch is installed,

open the switch.

i04155807

System Overview

4. Disconnect all electronic components from

the wiring harnesses. Include the following

components:

The engine has an electronic control system. The

system also monitors the Diesel Particulate Filter

(DPF) and the NOx Reduction System (NRS).

• Electronic components for the driven equipment

• ECM

The control system consists of the following

components:

• Sensors

• Electronically controlled valves

• Relays

• Electronic Control Module (ECM)

• Software (ﬂash ﬁle)

• Wiring

• Aftertreatment ID module

NOTICE

• Sensors

Do not use electrical components (ECM or ECM sen-

sors) or electronic component grounding points for

grounding the welder.

• Actuators

This document is printed from SPI². Not for RESALE

6

KENR9116-01

Troubleshooting Section

The following information provides a general

description of the control system. Refer to Systems

Operation, Testing, and Adjusting for detailed

information about the control system.

Electronic Control Circuit Diagram

g02476570

Illustration 2

Electronic control circuit diagram for the 1204E-E44 engine

This document is printed from SPI². Not for RESALE

KENR9116-01

7

Troubleshooting Section

g02476572

Illustration 3

Electronic control circuit diagram for the 1206E-E66 engine

Block Diagram

Refer to Illustration 4 and Illustration 5 for block

diagrams of the control system.

This document is printed from SPI². Not for RESALE

8

KENR9116-01

Troubleshooting Section

g02477761

Illustration 4

Block diagram for the 1204E and 1206E engines with a single turbocharger

(1) Air cleaner

(13) Air-to-air aftercooler

(25) Oil pressure sensor

(2) Air inlet temperature sensor

(3) NRS cooler

(14) Wastegate regulator

(15) NRS outlet pressure sensor

(16) Engine

(17) Coolant temperature sensor

(18) Primary speed/timing sensor

(19) Fuel injectors

(26) Barometric pressure sensor

(27) ECM

(28) Electric fuel lift pump

(29) Primary fuel ﬁlter

(4) Exhaust back pressure valve

(5) Diesel Oxidation Catalyst (DOC) and

Diesel Particulate Filter (DPF)

(6) DPF inlet temperature sensor

(7) Soot sensor

(8) Turbocharger

(9) NRS valve

(10) NRS temperature sensor

(11) NRS inlet pressure sensor

(12) NRS mixer

(30) In-line fuel strainer

(31) Intake manifold pressure sensor

(32) Intake manifold air temperature sensor

(33) Transfer pump inlet regulator

(34) Secondary fuel ﬁlter

(35) Fuel tank

(20) Return fuel cooler

(21) Return fuel pressure relief valve

(22) Secondary speed/timing sensor

(23) High-pressure fuel pump/transfer

pump/fuel temperature sensor

(24) Fuel rail pressure sensor

This document is printed from SPI². Not for RESALE

KENR9116-01

9

Troubleshooting Section

g02477778

Illustration 5

Block diagram for the 1204E-E44TTA engine with twin turbochargers

(1) Air cleaner

(13) Air-to-air aftercooler

(25) Oil pressure sensor

(2) Air inlet temperature sensor

(3) Exhaust back pressure valve

(4) Diesel Oxidation Catalyst (DOC) and

Diesel Particulate Filter (DPF)

(5) DPF inlet temperature sensor

(6) Soot sensor

(7) NRS cooler

(8) Turbochargers

(9) NRS valve

(14) Wastegate regulator

(15) NRS outlet pressure sensor

(16) Engine

(17) Coolant temperature sensor

(18) Primary speed/timing sensor

(19) Fuel injectors

(26) Barometric pressure sensor

(27) ECM

(28) Electric fuel lift pump

(29) Primary fuel ﬁlter

(30) In-line fuel strainer

(31) Intake manifold pressure sensor

(32) Intake manifold air temperature sensor

(33) Transfer pump inlet regulator

(34) Secondary fuel ﬁlter

(35) Fuel tank

(20) Return fuel cooler

(21) Return fuel pressure relief valve

(22) Secondary speed/timing sensor

(23) High-pressure fuel pump/transfer

pump/fuel temperature sensor

(24) Fuel rail pressure sensor

(10) NRS temperature sensor

(11) NRS inlet pressure sensor

(12) NRS mixer

System Operation

Engine Governor

The ECM governs the engine. The ECM determines

the timing, the injection pressure, and the amount

of fuel that is delivered to each cylinder. These

factors are based on the actual conditions and on the

desired conditions at any given time during starting

and operation.

The governor uses the throttle position sensor to

determine the desired engine speed. The governor

compares the desired engine speed to the actual

engine speed. The actual engine speed is determined

through interpretation of the signals that are received

by the ECM from the engine speed/timing sensors. If

the desired engine speed is greater than the actual

engine speed, the governor injects more fuel in order

to increase engine speed.

This document is printed from SPI². Not for RESALE

10

KENR9116-01

Troubleshooting Section

Fuel Injection

The ECM sends a high voltage signal to the injector

solenoids in order to energize the solenoids. By

controlling the timing and the duration of the high

voltage signal, the ECM can control the following

aspects of injection:

• Injection timing

• Fuel delivery

The ﬂash ﬁle inside the ECM establishes certain

limits on the amount of fuel that can be injected.

The FRC Fuel Limit is a limit that is based on the

intake manifold pressure. The FRC Fuel Limit is used

to control the air/fuel ratio for control of emissions.

When the ECM senses a higher intake manifold

pressure, the ECM increases the FRC Fuel Limit. A

higher intake manifold pressure indicates that there

is more air in the cylinder. When the ECM increases

the FRC Fuel Limit, the ECM allows more fuel into

the cylinder.

g01860934

Illustration 6

Typical example

The Rated Fuel Limit is a limit that is based on the

power rating of the engine and on the engine rpm.

The Rated Fuel Limit is like the rack stops and the

torque spring on a mechanically governed engine.

The Rated Fuel Limit provides the power curves

and the torque curves for a speciﬁc engine family

and a speciﬁc engine rating. All of these limits are

determined at the factory. These limits cannot be

changed.

The desired engine speed is typically determined by

one of the following conditions:

• The position of the throttle

• The desired engine speed in Power Take-Off (PTO)

Timing Considerations

Once the governor has determined the amount of

fuel that is required, the governor must determine

the timing of the fuel injection. Fuel injection timing is

determined by the ECM after considering input from

the following components:

Customer Parameters and Engine Speed

Governing

A unique feature with electronic engines is customer

speciﬁed parameters. These parameters allow the

owner of the machine to ﬁne-tune the ECM for engine

operation. Fine-tuning the ECM allows the machine

owner to accommodate the typical usage of the

machine and the power train of the machine.

• Coolant temperature sensor

• Intake manifold air temperature sensor

• Intake manifold pressure sensor

• Barometric pressure sensor

Many of the customer parameters provide additional

restrictions on the actions that will be performed by

the ECM in response to input from the operator. The

PTO Top Engine Limit is an engine rpm limit that is

used by the ECM to limit the fuel during operation of

the PTO. The ECM will not fuel the injectors above

this rpm.

The ECM adjusts timing for optimum engine

performance and fuel economy. Actual timing and

desired timing cannot be viewed with the electronic

service tool. The ECM determines the location of

top center of the number one cylinder from the

signals that are provided by the engine speed/timing

sensors. The ECM determines when injection should

occur relative to top center position. The ECM then

provides the signal to the injector at the desired time.

Some parameters are intended to notify the operator

of potential engine damage (engine monitoring

parameters). Some parameters enhance fuel

economy (machine speed, engine speed limit,

and idle shutdown). Other parameters are used to

enhance the engine installation into the machine.

Other parameters are used to provide operating

information to the owner of the machine.

This document is printed from SPI². Not for RESALE

KENR9116-01

11

Troubleshooting Section

Other ECM Functions for

Performance

“Lifetime Total Engine Revolutions” is the total

number of revolutions that have been completed by

the engine crankshaft.

The ECM can also provide enhanced control of the

engine for machine functions such as controlling the

cooling fan. Refer to Troubleshooting, “Conﬁguration

Parameters” for supplemental information about the

systems that can be monitored by the ECM in order

to provide enhanced machine performance, fuel

economy, and convenience for the operator.

“Average Load Factor” provides relative engine

operating information. “Average Load Factor”

compares actual operating information of the engine

to the maximum engine operation that is available.

“Average Load Factor” is determined by using “Total

Max Fuel”, “Total Idle Fuel”, and “Total Fuel”. All of

these parameters are available with the electronic

service tool. These parameters are available within

the menu for “Current Totals”.

ECM Lifetime Totals

The ECM maintains total data of the engine for the

following parameters:

Programmable Parameters

Certain parameters that affect engine operation

may be changed with the electronic service tool.

The parameters are stored in the ECM, and the

parameters are protected from unauthorized changes

by passwords. These parameters are either system

conﬁguration parameters or customer parameters.

• “Total Operating Hours”

• “Engine Lifetime Hours”

• “Total Idle Time”

• “Total Idle Fuel”

System conﬁguration parameters are set at the

factory. System conﬁguration parameters affect

emissions or power ratings within an engine family.

Factory passwords must be obtained and factory

passwords must be used to change the system

conﬁguration parameters.

• “Total Fuel”

• “Total Max Fuel”

• “Engine Starts”

Customer parameters are variable. Customer

parameters affect the following characteristics within

the limits that are set by the factory, by the monitoring

system, and by PTO operation:

• “Lifetime Total Engine Revolutions”

• “Average Load Factor”

The “Total Operating Hours” is the operating hours of

the engine. The operating hours do not include the

time when the ECM is powered but the engine is not

running.

• Rpm ratings

• Power ratings

Customer passwords may be required to change

customer speciﬁed parameters.

The “Engine Lifetime Hours” is the number of hours

when electrical power has been applied to the

engine. These hours will include the time when the

ECM is powered but the engine is not running.

Some of the parameters may affect engine operation

in an unusual way. An operator might not expect

this type of effect. Without adequate training,

these parameters may lead to power complaints

or performance complaints even though the

performance of the engine is to the speciﬁcation.

“Total Idle Time” and “Total Idle Fuel” can include

operating time when the engine is not operating

under a load.

Fuel Information can be displayed in US gallons or

in liters.

Refer to Troubleshooting, “Conﬁguration Parameters”

for additional information on this subject.

“Total Fuel” is the total amount of fuel that is

consumed by the engine during operation.

Passwords

“Total Max Fuel” is the maximum amount of fuel that

could have been consumed by the engine during

operation.

System conﬁguration parameters are protected by

factory passwords. Factory passwords are calculated

on a computer system that is available only to

Perkins Distributors. Since factory passwords contain

alphabetic characters, only the electronic service

tool may change system conﬁguration parameters.

System conﬁguration parameters affect the power

rating family or emissions.

“Engine Starts” is the total number of times when the

engine has been started.

This document is printed from SPI². Not for RESALE

12

KENR9116-01

Troubleshooting Section

Customer parameters can be protected by

customer passwords. The customer passwords are

programmed by the customer. Factory passwords

can be used to change customer passwords if

customer passwords are lost.

Communication Adapter Tool – The

communication adapter provides a communication

link between the ECM and the electronic service tool.

Coolant Temperature Sensor – The coolant

temperature sensor detects the engine coolant

temperature for all normal operating conditions and

for engine monitoring.

Refer to Troubleshooting, “Factory Passwords” for

additional information on this subject.

Data Link – The data link is a serial communication

port that is used for communication with other devices

such as the electronic service tool.

i04156374

Glossary

Derate – Certain engine conditions will generate

event codes. Also, engine may be derated. The map

for the engine derate is programmed into the ECM

software. The type of derate can be one or more of

three types: reduction of rated power, reduction of

rated engine speed, and reduction of rated machine

speed for OEM products.

Active Diagnostic Code – An active diagnostic

code alerts the operator or the service technician that

an electronic system malfunction is currently present.

Refer to the term “Diagnostic Code” in this glossary.

Aftertreatment – Aftertreatment is a system that is

used to remove pollutants from exhaust gases. The

system consists of a Diesel Oxidation Catalyst (DOC)

and a Catalyzed Diesel Particulate Filter (CDPF).

Desired Engine Speed – The desired engine speed

is input to the electronic governor within the ECM.

The electronic governor uses the signal from the

throttle position sensor, the engine speed/timing

sensor, and other sensors in order to determine the

desired engine speed.

Alternating Current (AC) – Alternating current is an

electric current that reverses direction at a regular

interval that is reoccurring.

Diagnostic Trouble Code – A diagnostic trouble

code is sometimes referred to as a fault code. These

codes indicate an electronic system malfunction.

Before Top Center (BTC) – BTC is the 180 degrees

of crankshaft rotation before the piston reaches the

top center position in the normal direction of rotation.

Diagnostic Lamp – The diagnostic lamp is also

called the warning lamp. The diagnostic lamp is used

to warn the operator of the presence of an active

diagnostic code. The lamp may not be included in

all applications.

Breakout Harness – A breakout harness is a

test harness that is designed to connect into the

engine harness. This connection allows a normal

circuit operation and the connection simultaneously

provides a Breakout T in order to measure the

signals.

Diesel Oxidation Catalyst – The Diesel Oxidation

Catalyst is also known as the (DOC). The DOC is a

device in the exhaust system that oxidizes certain

elements in the exhaust gases. These elements can

include carbon monoxide (CO), hydrocarbons and

the soluble organic fractions (SOF) of particulate

matter.

Bypass Circuit – A bypass circuit is a circuit that is

used as a substitute circuit for an existing circuit. A

bypass circuit is typically used as a test circuit.

CAN Data Link (see also J1939 CAN Data Link) –

The CAN Data Link is a serial communications

port that is used for communication with other

microprocessor-based devices.

Digital Sensor Return – The common line (ground)

from the ECM is used as ground for the digital

sensors.

Catalyzed Diesel Particulate Filter – The Catalyzed

Diesel Particulate Filter (CDPF) ﬁlters particulates

from the exhaust gases. A coating on the internal

surfaces reacts with the hot exhaust gases in order

to burn off the particulates. This process prevents the

CDPF from becoming blocked with soot.

Digital Sensors – Digital sensors produce a pulse

width modulated signal. Digital sensors are supplied

with power from the ECM.

Digital Sensor Supply – The power supply for the

digital sensors is provided by the ECM.

Clean Emissions Module – The Clean Emissions

Module (CEM) includes all the components of the

aftertreatment system.

Direct Current (DC) – Direct current is the type of

current that ﬂows consistently in only one direction.

DT, DT Connector, or Deutsch DT – This design is

a type of connector that is used on this engine. The

connectors are manufactured by Deutsch.

Code – Refer to “Diagnostic Trouble Code”.

This document is printed from SPI². Not for RESALE

KENR9116-01

13

Troubleshooting Section

Duty Cycle – Refer to “Pulse Width Modulation”.

Failure Mode Identiﬁer (FMI) – This identiﬁer

indicates the type of failure that is associated with

the component. The FMI has been adopted from the

SAE practice of J1587 diagnostics. The FMI follows

the parameter identiﬁer (PID) in the descriptions of

the fault code. The descriptions of the FMIs are in

the following list.

Electronic Engine Control – The electronic

engine control is a complete electronic system.

The electronic engine control monitors the engine

operation under all conditions. The electronic engine

control also controls the engine operation under all

conditions.

0 – The data is valid but the data is above the normal

Electronic Control Module (ECM) – The ECM

is the control computer of the engine. The ECM

provides power to the electronics. The ECM monitors

data that is input from the sensors of the engine. The

ECM acts as a governor in order to control the speed

and the power of the engine.

operational range.

1 – The data is valid but the data is below the normal

operational range.

2 – The data is erratic, intermittent, or incorrect.

Electronic Service Tool – The electronic service

tool allows a computer (PC) to communicate with the

ECM.

3 – The voltage is above normal or the voltage is

shorted high.

4 – The voltage is below normal or the voltage is

shorted low.

Engine Monitoring – Engine Monitoring is the part

of the electronic engine control that monitors the

sensors. Engine monitoring also warns the operator

of detected problems.

5 – The current is below normal or the circuit is open.

6 – The current is above normal or the circuit is

grounded.

Engine Oil Pressure Sensor – The engine oil

pressure sensor measures engine oil pressure. The

sensor sends a signal to the ECM that is dependent

on the engine oil pressure.

7 – The mechanical system is not responding

properly.

Engine Speed/Timing Sensor – An engine

speed/timing sensor is a hall effect switch that

provides a digital signal to the ECM. The ECM

interprets this signal as the crankshaft position and

the engine speed. Two sensors are used to provide

the speed and timing signals to the ECM. The primary

sensor is associated with the crankshaft and the

secondary sensor is associated with the camshaft.

8 – There is an abnormal frequency, an abnormal

pulse width, or an abnormal time period.

9 – There has been an abnormal update.

10 – There is an abnormal rate of change.

11 – The failure mode is not identiﬁable.

12 – The device or the component is damaged.

13 – The device requires calibration.

Ether Injection – Ether injection is a starting aid in

cold conditions. Glow plugs are used as a starting

aid when the ambient temperature is between 5° C

(41° F) and −25° C (−13° F). At a temperature that

is lower than −25° C (−13° F), the glow plugs are

disabled and ether injection is used.

14 – There is a special instruction for the device.

15 – The signal from the device is high (least severe).

Event Code – An event code may be activated

in order to indicate an abnormal engine operating

condition. These codes usually indicate a mechanical

problem instead of an electrical system problem.

16 – The signal from the device is high (moderate

severity).

17 – The signal from the device is low (least severe).

Exhaust Back Pressure Valve – The exhaust back

pressure valve regulates the gas pressure in the

exhaust system. The valve can restrict the ﬂow of

exhaust gases in order to increase the exhaust back

pressure. An increase in exhaust back pressure will

increase the temperature of the exhaust gases. The

increase in temperature will improve the process that

burns off the soot in the CDPF.

18 – The signal from the device is low (moderate

severity).

19 – There is an error in the data from the device.

31 – The device has failed and the engine has shut

down.

This document is printed from SPI². Not for RESALE

14

KENR9116-01

Troubleshooting Section

Flash File – This ﬁle is software that is inside

the ECM. The ﬁle contains all the instructions

(software) for the ECM and the ﬁle contains the

performance maps for a speciﬁc engine. The ﬁle may

be reprogrammed through ﬂash programming.

Harness – The harness is the bundle of wiring

(loom) that connects all components of the electronic

system.

Hertz (Hz) – Hertz is the measure of electrical

frequency in cycles per second.

Flash Programming – Flash programming is the

method of programming or updating an ECM with

an electronic service tool over the data link instead

of replacing components.

High Pressure Fuel Pump – This pump is a device

that supplies fuel under pressure to the fuel rail

(high-pressure fuel rail).

FRC – See “Fuel Ratio Control”.

High Pressure Fuel Rail – See “Fuel Rail”.

Fuel Pump – See “High Pressure Fuel Pump”.

Injector Trim Codes – Injector trim codes are codes

that contain 30 characters. The codes are supplied

with new injectors. The code is input through the

electronic service tool into the ECM. The injector trim

codes compensate for variances in manufacturing

of the electronic unit injector and for the life of the

electronic unit injector.

Fuel Rail – This item is sometimes referred to as the

High Pressure Fuel Rail. The fuel rail supplies fuel to

the electronic unit injectors. The high-pressure fuel

pump and the fuel rail pressure sensor work with the

ECM in order to maintain the desired fuel pressure

in the fuel rail. This pressure is determined by

calibration of the engine in order to enable the engine

to meet emissions and performance requirements.

Intake Manifold Air Temperature Sensor – The

intake manifold air temperature sensor detects the

air temperature in the intake manifold. The ECM

monitors the air temperature and other data in the

intake manifold in order to adjust injection timing and

other performance functions.

Fuel Rail Pressure Sensor – The fuel rail pressure

sensor sends a signal to the ECM that is dependent

on the pressure of the fuel in the fuel rail.

Fuel Ratio Control (FRC) – The FRC is a limit that

is based on the control of the ratio of the fuel to air.

The FRC is used for purposes of emission control.

When the ECM senses a higher intake manifold

air pressure (more air into the cylinder), the FRC

increases the FRC Limit (more fuel into the cylinder).

Intake Manifold Pressure Sensor – The Intake

Manifold Pressure Sensor measures the pressure

in the intake manifold. The pressure in the intake

manifold may be different to the pressure outside

the engine (atmospheric pressure). The difference

in pressure may be caused by an increase in air

pressure by a turbocharger.

Full Load Setting (FLS) – The FLS is the parameter

that represents the fuel system adjustment. This

adjustment is made at the factory in order to

ﬁne-tune the fuel system. This parameter must be

programmed.

Integrated Electronic Controls – The engine is

designed with the electronic controls as a necessary

part of the system. The engine will not operate

without the electronic controls.

Full Torque Setting (FTS) – The FTS is the

parameter that represents the adjustment for the

engine torque. This adjustment is made at the factory

in order to ﬁne-tune the fuel system. This adjustment

is made with the FLS. This parameter must be

programmed.

J1939 CAN Data Link – This data link is a SAE

standard diagnostic communications data link that is

used to communicate between the ECM and other

electronic devices.

Logged Diagnostic Codes – Logged diagnostic

codes are codes which are stored in the memory.

These codes are an indicator of possible causes for

intermittent problems. Refer to the term “Diagnostic

Trouble Codes” for more information.

Glow Plug – The glow plug is an optional starting aid

for cold conditions. One glow plug is installed in each

combustion chamber in order to improve the ability of

the engine to start. The ECM uses information from

the engine sensors to determine when the glow plug

relay must provide power to each glow plug. Each

of the glow plugs then provides a hot surface in the

combustion chamber in order to vaporize the mixture

of air and fuel. The vaporization improves ignition

during the compression stroke of the cylinder.

NOx Reduction System – The NOx Reduction

System recycles a portion of the exhaust gases back

into the inlet air. The recirculation reduces the oxides

of nitrogen (NOx) in the exhaust gases. The recycled

exhaust gas passes through a cooler before being

introduced into the inlet air.

Glow Plug Relay – The glow plug relay is controlled

by the ECM in order to provide high current to the

glow plugs.

OEM – OEM is an abbreviation for the Original

Equipment Manufacturer. The OEM is the

manufacturer of the machine or the vehicle that uses

the engine.

This document is printed from SPI². Not for RESALE

KENR9116-01

15

Troubleshooting Section

Open Circuit – An open circuit is a condition that is

caused by an open switch, or by an electrical wire

or a connection that is broken. When this condition

exists, the signal o, r the supply voltage can no longer

reach the intended destination.

Parameter – A parameter is a value or a limit that is

programmable. A parameter helps determine speciﬁc

characteristics or behaviors of the engine.

Password – A password is a group of numeric

characters or a group of alphanumeric characters

that is designed to restrict access to parameters. The

electronic system requires correct passwords in order

to change some parameters (Factory Passwords).

Refer to Troubleshooting, “Factory Passwords” for

more information.

Personality Module – See “Flash File”.

Power Cycling – Power cycling refers to the action

of cycling the keyswitch from any position to the OFF

position, and to the START/RUN position.

g01858875

Illustration 7

Rated Fuel Limit – The rated fuel limit is a limit that

is based on the power rating of the engine and on the

engine rpm. The Rated Fuel Limit enables the engine

power and torque outputs to conform to the power

and torque curves of a speciﬁc engine model. These

limits are in the ﬂash ﬁle and these limits cannot be

changed.

Pressure Limiting Valve (PLV) – The PLV is a valve

in the fuel rail that prevents excessive pressure. The

PLV will reduce the pressure to a safe level that will

limit engine operation but the reduced pressure will

not stop the engine.

Primary Speed/Timing Sensor – This sensor

determines the position of the crankshaft during

engine operation. If the primary speed/timing

sensor fails during engine operation, the secondary

speed/timing sensor is used to provide the signal.

Reference Voltage – Reference voltage is a

regulated voltage and a steady voltage that is

supplied by the ECM to a sensor. The reference

voltage is used by the sensor to generate a signal

voltage.

Pulse Width Modulation (PWM) – The PWM is a

signal that consists of pulses that are of variable

width. These pulses occur at ﬁxed intervals. The ratio

of “TIME ON” versus “TIME OFF” can be varied. This

ratio is also referred to as a duty cycle.

Relay – A relay is an electromechanical switch. A

ﬂow of electricity in one circuit is used to control the

ﬂow of electricity in another circuit. A small current or

voltage is applied to a relay in order to switch a much

larger current or voltage.

Secondary Speed/Timing Sensor – This sensor

determines the position of the camshaft during engine

operation. If the primary speed/timing sensor fails

during engine operation, the secondary speed/timing

sensor is used to provide the signal.

Sensor – A sensor is a device that is used to

detect the current value of pressure or temperature,

or mechanical movement. The information that is

detected is converted into an electrical signal.

Short Circuit – A short circuit is a condition that has

an electrical circuit that is inadvertently connected to

an undesirable point. An example of a short circuit

is a wire which rubs against a vehicle frame and

this rubbing eventually wears off the wire insulation.

Electrical contact with the frame is made and results

in a short circuit.

This document is printed from SPI². Not for RESALE

16

KENR9116-01

Troubleshooting Section

Signal – The signal is a voltage or a waveform that

is used in order to transmit information typically from

a sensor to the ECM.

Wastegate – The wastegate is a device in a

turbocharged engine that controls the maximum

boost pressure that is provided to the inlet manifold.

Suction Control Valve (SCV) – The SCV is a control

device in the high-pressure fuel pump. The valve

controls the pressure in the fuel rail by varying the

amount of fuel that enters the chambers in the pump.

Wastegate Regulator – The wastegate regulator

controls the pressure in the intake manifold to a

value that is determined by the ECM. The wastegate

regulator provides the interface between the ECM

and the mechanical system. The wastegate regulates

intake manifold pressure to the desired value that is

determined by the software.

Supply Voltage – The supply voltage is a continuous

voltage that is supplied to a component. The power

may be generated by the ECM or the power may be

battery voltage that is supplied by the engine wiring.

i04084033

Suspect Parameter Number (SPN) – The SPN is a

J1939 number that identiﬁes the speciﬁc component

of the electronic control system that has experienced

a diagnostic code.

Electronic Service Tools

Perkins electronic service tools are designed to help

the service technician:

System Conﬁguration Parameters – System

conﬁguration parameters are parameters that affect

emissions and/or operating characteristics of the

engine.

• Retrieve diagnostic codes.

• Diagnose electrical problems.

• Read parameters.

Tattletale – Certain parameters that affect the

operation of the engine are stored in the ECM.

These parameters can be changed by use of the

electronic service tool. The tattletale logs the number

of changes that have been made to the parameter.

The tattletale is stored in the ECM.

• Program parameters.

• Install injector trim codes.

Throttle Position – The throttle position is the

interpretation by the ECM of the signal from the

throttle position sensor or the throttle switch.

Required Service Tools

Table 1

Throttle Position Sensor – The throttle position

sensor is a sensor that is normally connected to an

accelerator pedal or a hand lever. This sensor sends

a signal to the ECM that is used to calculate desired

engine speed.

Required Service Tools

Part Number

CH11155

Description

Crimp Tool (12−AWG TO 18−AWG)

Wire Removal Tool

2900A019

Throttle Switch – The throttle switch sends a signal

to the ECM that is used to calculate desired engine

speed.

27610285

Removal Tool

-

Suitable Digital Multimeter

Top Center Position – The top center position refers

to the crankshaft position when the engine piston

position is at the highest point of travel. The engine

must be turned in the normal direction of rotation in

order to reach this point.

Two short jumper wires are needed to check the

continuity of some wiring harness circuits by shorting

two adjacent terminals together in a connector. A

long extension wire may also be needed to check the

continuity of some wiring harness circuits.

Total Tattletale – The total tattletale is the total

number of changes to all the parameters that are

stored in the ECM.

Optional Service Tools

Table 2 lists the optional service tools that can be

used when the engine is serviced.

Wait To Start Lamp – This lamp is included in the

cold starting aid circuit in order to indicate when the

wait to start period is active. The lamp will go off

when the engine is ready to be started. The glow

plugs may not have deactivated.

This document is printed from SPI². Not for RESALE

KENR9116-01

17

Troubleshooting Section

Table 2

Table 3

Part Number

U5MK1092

Description

Service Tools for the Use of the Electronic

Service Tool

Spoon Probe Kit(MULTIMETER)

Part

Description

-

or

-

Suitable Digital Pressure Indicator

or

Engine Pressure Group

Number

-(1)

Single Use Program License

-

-

-

(1)

Suitable Battery Load Tester

Data Subscription for All Engines

Suitable Temperature Adapter

(MULTIMETER)

Communication Adapter (Electronic

Service Tool to the ECM interface)

27610251

27610164

28170107

2900A038

Bypass Harness As

Harness as

Adapter Cable As

(1) Refer to Perkins Engine Company Limited.

Note: For more information on the Electronic

Service Tool and the PC requirements, refer to the

documentation that accompanies the software for the

Electronic Service Tool.

Perkins Electronic Service Tool

The Perkins Electronic Service Tool can display the

following information:

Connecting the Electronic Service Tool

and the Communication Adapter II

• Status of all pressure sensors and temperature

sensors

• Programmable parameter settings

• Active diagnostic codes and logged diagnostic

codes

• Logged events

• Histograms

The Electronic Service Tool can also be used to

perform the following functions:

• Diagnostic tests

• Sensor calibrations

• Programming of ﬂash ﬁles and injector trim codes

• Parameter programming

• Copy conﬁguration function for ECM replacement

• Data logging

• Graphs (real time)

Table 3 lists the service tools that are required in

order to use the Electronic Service Tool.

g01121866

Illustration 8

(1) Personal Computer (PC)

(2) Adapter Cable (Computer Serial Port)

(3) Communication Adapter II

(4) Adapter Cable Assembly

Note: Items (2), (3) and (4) are part of the

Communication Adapter II kit.

Use the following procedure in order to connect

the Electronic Service Tool and the Communication

Adapter II.

This document is printed from SPI². Not for RESALE

18

KENR9116-01

Troubleshooting Section

1. Turn the keyswitch to the OFF position.

Warning Lamp

2. Connect cable (2) between the “COMPUTER”

end of communication adapter (3) and the RS232

serial port of PC (1).

Lamp check – When the keyswitch is turned to ON,

the lamp will come on for 2 seconds. The lamp will

then go off unless there is an active warning.

Note: The Adapter Cable Assembly (4) is required to

connect to the USB port on computers that are not

equipped with an RS232 serial port.

Flashing – The lamp will be ﬂashing when a

“warning” or a “warning and derate” is active. This

includes low oil pressure.

3. Connect cable (4) between the “DATA LINK” end

of communication adapter (3) and the service tool

connector.

On – The lamp will be on when the shutdown level

has been reached. The “Shutdown” lamp will also

be on.

4. Place the keyswitch in the ON position. If the

Electronic Service Tool and the communication

adapter do not communicate with the Electronic

Control Module (ECM), refer to the diagnostic

procedure Troubleshooting, “Electronic Service

Tool DoesNot Communicate”.

Wait to Start Lamp

Lamp check – When the keyswitch is turned to ON,

the lamp will come on for 2 seconds. The lamp will

then go off unless “Wait to Start” is active.

On – The lamp is on during a “Wait to Start” period.

i03834091

Low Oil Pressure

Indicator Lamps

Lamp check – When the keyswitch is turned to ON,

the lamp will come on for 2 seconds. The lamp will

then go off unless there is an active warning.

Indicator Lamps

On – The lamp will come on when a low oil pressure

event is detected. The “Warning” lamp and the

“Shutdown” lamp may also come on.

Four lamps are available as options. The “Shutdown”

lamp and the “Warning” lamp will normally be installed

in the application. Dedicated optional lamps for other

items may also be installed. The remaining optional

lamps are “Wait to start” and “Low oil pressure”.

Note: On a cold start, when the Electronic Control

Module (ECM) determines that it is necessary for the

glow plugs to be activated prior to starting, a lamp

output will indicate that the operator needs to “Wait

to Start”. It is possible that starting aids may be used

during the cranking of the engine. Starting aids may

be used if the engine has previously been started.

The “Wait to Start” lamp will not be active in these

conditions.

The “Shutdown” lamp and the “Warning” lamp can

also be used to indicate a diagnostic code by use of

the “Flash Code” feature. The “Flash Code” feature

can be used to indicate all active diagnostic codes

and logged diagnostic codes.

Functions of the Lamps

Color of Lamps

Shutdown Lamp

Typically, the “Shutdown” lamp is colored red and the

“Warning” lamp is colored amber. The other lamps

are optional.

Lamp check – When the keyswitch is turned to ON,

the lamp will come on for 2 seconds. The lamp will

then go off unless there is an active warning.

Flashing – The lamp will be ﬂashing when a derate

is active or when a derate is present because of

an active diagnostic code. An example of an active

diagnostic code is “System Voltage High”.

On – The lamp will be on when the shutdown level

in the engine protection strategy has been reached.

The “Warning” lamp will also be on.

This document is printed from SPI². Not for RESALE

KENR9116-01

19

Troubleshooting Section

Operation of the Indicator Lamps

Table 4

Warning

Lamp

(Alert

Shutdown

Lamp

(Action

Lamp State

Lamp Check

No Faults

Description of the Indication

Engine State

Lamp)

Lamp)

On

On

When the keyswitch is moved to the

ON position, the lamps come on for

a period of 2 seconds and the lamps

will then go off.

The keyswitch is in the ON position but

the engine has not yet been cranked.

Off

On

Off

Off

With the engine in operation, there

are no active warnings, diagnostic

codes or event codes.

The engine is operating with no detected

faults.

Active

Diagnostic

If the warning lamp comes on during

engine operation, this indicates

that an active diagnostic code (an

electrical fault) is present.

The engine is operating normally but

there is one or more faults with the

electronic management system for the

engine.

On

Flashing

Derate

(A derate is

caused by

certain active

codes.)

If the warning lamp comes on and the The engine is operating but there is one

shutdown lamp ﬂashes during engine or more active diagnostic codes that

operation, this indicates that an active have initiated an engine derate.

diagnostic code (an electrical fault) is

present. The diagnostic is sufﬁciently

serious in order to cause an engine

derate.

Flashing

Off

Warning

(Warning only) during operation of the engine,

the lamp indicates that one or

When the warning lamp ﬂashes

The engine is operating normally.

However, there is one or more of the

monitored engine parameters that are

outside of the range that is acceptable.

more of the warning values for the

engine protection strategy has been

exceeded. However, the value has

not been exceeded to a level that will

cause a derate or a shutdown.

Flashing

Flashing

Off

Warning

(Warning only) Diesel Particulate Filter (DPF).

There is a high soot loading in the

The soot loading in the DPF has

reached 100%. The engine will be

derated. The lamp warns the operator

that the engine needs to be operated in

a mode that promotes regeneration.

Flashing

Derate

(Warning and

Derate)

If both the warning lamp and

shutdown lamp ﬂash during operation one or more of the monitored engine

of the engine, the lamps indicate that parameters is outside of the acceptable

The engine is operating. However,

one or more of the values for the

range. The acceptable range has been

engine protection strategy have been exceeded to a level which requires a

exceeded beyond the level that will

cause an engine derate.

warning and an engine derate.

Flashing

On

On

On

Very high DPF The soot loading in the DPF is high.

soot loading

The soot loading in the DPF has reached

120%. The engine must be operated in

a mode that promotes regeneration.

Engine

Shutdown

If both the warning lamp and the

shutdown lamp come on during

engine operation, this indicates one

of the following conditions.

The engine is either shutdown or an

engine shutdown is imminent. One or

more monitored engine parameters

have exceeded the limit for an engine

shutdown. This pattern of lamps can be

caused by the detection of a serious

active diagnostic code.

1. One or more of the shutdown

values for the engine protection

strategy has been exceeded.

2. A serious active diagnostic code

has been detected.

After a short period of time, the

engine will shut down.

This document is printed from SPI². Not for RESALE

20

KENR9116-01

Troubleshooting Section

Flash Codes

The “Flash Code” feature is used to ﬂash the code

of all active diagnostic codes and logged diagnostic

codes.

The sequence for the ﬂash code is started by moving

the keyswitch to “Off” and then moving the keyswitch

to “On” twice within a period of three seconds. After

a delay of 2 seconds, the “Shutdown” lamp will ﬂash

once for a period of half a second. This sequence

indicates the start of the active fault codes. After

a further delay of 2 seconds, the “Warning” lamp

will ﬂash repeatedly in order to indicate the active

diagnostic codes. Each ﬂash will be on for half a

second and off for 300 milliseconds. The “Warning”

lamp will remain off for 2 seconds between each digit

of a code. If there is more than one active diagnostic

code, the “Shutdown” lamp will go off for 2 seconds.

The lamp will then come on for a period of half a

second. The “Warning” lamp will go off for a period of

2 seconds before starting the next code. If there are

no active diagnostic codes, the “Warning” lamp will

ﬂash the code “551”. Refer to Troubleshooting Guide,

“No Diagnostic Code Detected”.

As an example, an active diagnostic code of “21” is

indicated by the “Warning” lamp coming on for 500

ms, then off for 300 ms, then on for 500 ms, then off

for 2000 ms, then on for 500 ms and then off.

g01779334

Illustration 9

Timing of the ﬂash codes

After all of the active diagnostic codes have been

displayed, the “Shutdown” lamp will go off for 2

seconds. The “Shutdown” lamp will ﬂash twice in

order to indicate the start of the sequence that will

display the logged diagnostic codes. The process for

ﬂashing logged diagnostic codes is identical to the

process for ﬂashing active diagnostic codes.

Note: If there are no logged codes then the “551”

code should be ﬂashed again.

This document is printed from SPI². Not for RESALE

KENR9116-01

21

Troubleshooting Section

After all of the codes have been displayed, the

“Shutdown” lamp will ﬂash 3 times in order to

indicate that there are no further codes. Cycling the

keyswitch twice within a period of 3 seconds will

start the process again. All codes will be displayed in

ascending numerical order.

Note: If an ECM is to be used as a test ECM, “Test

ECM Mode” must be selected on the electronic

service tool before the engine serial number is

entered.

Use the electronic service tool to read the parameters

in the suspect ECM. Record the parameters in

the suspect ECM. Install the ﬂash ﬁle into the new

ECM. After the ECM is installed on the engine, the

parameters must be programmed into the new ECM.

Refer to the Troubleshooting Guide, “Diagnostic

Code Cross Reference” for the diagnostic code that

relates to the ﬂash code.

Note: Flash codes are always sent in ascending

numerical order.

Note: When a new ECM is not available, an ECM

can be used from an engine that is not in service.

The ECM must have the same serial number

sufﬁx. Ensure that the replacement ECM and the

part number for the ﬂash ﬁle match the suspect

ECM. Be sure to record the parameters from the

replacement ECM. Use the “Copy Conﬁguration ECM

Replacement” function in the electronic service tool.

i04319696

Replacing the ECM

NOTICE

If the ﬂash ﬁle and engine application are not matched,

engine damage may result.

NOTICE

Care must be taken to ensure that ﬂuids are contained

during performance of inspection, maintenance, test-

ing, adjusting, and repair of the product. Be prepared

to collect the ﬂuid with suitable containers before

opening any compartment or disassembling any com-

ponent containing ﬂuids.

Perform the following procedure in order to replace

the ECM.

1. Connect the electronic service tool to the

diagnostic connector.

Dispose of all ﬂuids according to local regulations and

mandates.

2. Use the “Copy Conﬁguration ECM Replacement”

function from the electronic service tool. If the

process is successful, proceed to Step 4. If the

“Copy Conﬁguration” failed, proceed to Step 3.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Note: Record any Logged Faults and Events for your

records.

The engine is equipped with an Electronic Control

Module (ECM). The ECM contains no moving parts.

Follow the troubleshooting procedures in this manual

in order to be sure that replacing the ECM will correct

the fault. Verify that the suspect ECM is the cause

of the fault.

3. Record the following parameters:

•

•

•

Record all of the parameters on the

“Conﬁguration” screen.

Record all of the parameters on the “Throttle

Conﬁguration” screen.

Note: Ensure that the ECM is receiving power

and that the ECM is properly grounded before

replacement of the ECM is attempted. Refer to the

schematic diagram.

Record all of the parameters on the “Mode

Conﬁguration” screen.

• Record the serial numbers of the electronic unit

injectors. The injector serial numbers are shown

on the “Injector Trim Calibration” screen.

A test ECM can be used in order to determine if the

ECM on the engine is faulty. Install a test ECM in

place of the suspect ECM. Install the ﬂash ﬁle with

the correct part number into the test ECM. Program

the parameters for the test ECM. The parameters

must match the parameters in the suspect ECM.

Refer to the following test steps for details. If the

test ECM resolves the fault, reconnect the suspect

ECM. Verify that the fault returns. If the fault returns,

replace the ECM.

Note: If the parameters cannot be read, the

parameters must be obtained elsewhere. Some

parameters are stamped on the engine information

plate, but most parameters must be obtained from

the PTMI data on the Perkins web site.

4. Remove power from the ECM.

This document is printed from SPI². Not for RESALE

22

KENR9116-01

Troubleshooting Section

5. Remove the ECM. Refer to Disassembly and

Assembly, “Electronic Control Module - Remove

and Install”.

Diagnostic Trouble Code – When a fault in the

electronic system is detected, the ECM generates a

diagnostic trouble code. The diagnostic trouble code

indicates the speciﬁc fault in the circuitry.

6. Install the replacement ECM. Refer to Disassembly

and Assembly, “Electronic Control Module -

Remove and Install”.

Diagnostic codes can have two different states:

• Active

7. If the replacement ECM is to be used as a test

ECM, select “Test ECM Mode” on the electronic

service tool.

• Logged

Active Code – An active diagnostic code indicates

that an active fault has been detected by the control

system. Active codes require immediate attention.

Always service active codes prior to servicing logged

codes.

8. Download the ﬂash ﬁle.

a. Connect the electronic service tool to the

diagnostic connector.

b. Select “WinFlash” from the “Utilities” menu of

the electronic service tool.

Logged Code – Every generated code is stored

in the permanent memory of the ECM. The codes

are logged for 100 operating hours unless a code is

cleared by use of the electronic service tool.

c. Select the downloaded ﬂash ﬁle.

9. If necessary, use the electronic service tool to clear

the rating interlock. To clear the rating interlock,

enter the factory password when the electronic

service tool is ﬁrst connected. Activating the Test

ECM mode will also clear the rating interlock.

Logged codes may not indicate that a repair is

needed. The fault may have been temporary. The

fault may have been resolved since the logging

of the code. If the system is powered, an active

diagnostic trouble code may be generated whenever

a component is disconnected. When the component

is reconnected, the code is no longer active. Logged

codes may be useful to help troubleshoot intermittent

faults. Logged codes can also be used to review the

performance of the engine and the electronic system.

10. Use the electronic service tool to program the

parameters. Perform the following procedure.

a. If the “Copy Conﬁguration” procedure was

successful, use the “Copy Conﬁguration, ECM

Replacement” function to load the conﬁguration

ﬁle into the ECM.

i04215569

Sensors and Electrical

Connectors

Note: During the following procedure, factory

passwords may be required.

b. If the “Copy Conﬁguration” procedure failed,

conﬁgure the parameters individually. The

parameters should match the parameters from

step 3.

The Electronic Control Module (ECM) and most

of the engine sensors are located on the left side

of the engine. For the 1204E-E44 engine, refer to

Illustration 10. For the remaining sensors that are

attached to the 1204E-E44 engine, refer to Illustration

12. For the 1206E-E66 engine, refer to Illustration 14

. For the remaining sensors that are attached to the

1206E-E66 engine, refer to Illustration 16. For the

sensors and components on the Clean Emissions

Module (CEM), refer to Illustration 18.

Perform the “Fuel System Veriﬁcation Test”.

11. Check for logged diagnostic codes. Factory

passwords are required to clear logged events.

i03951470

Self-Diagnostics

Note: In the following illustrations, some components

have been removed in order to improve visibility.

The Electronic Control Module (ECM) can detect

faults in the electronic system and with engine

operation. A self-diagnostic check is also performed

whenever power is applied to the ECM.

When a fault is detected, a diagnostic trouble code

is generated. This code conforms to the SAE J1939

standard. An alarm may also be generated.

This document is printed from SPI². Not for RESALE

KENR9116-01

23

Troubleshooting Section

Typical 1204E-E44 Engine

g02479176

Illustration 10

Sensor locations on the left side of a typical 1204E-E44 engine

(1) Coolant temperature sensor

(2) Intake manifold air temperature sensor

(3) Intake manifold pressure sensor

(4) Fuel rail pressure sensor

(5) Water-in-fuel switch

(8) Fuel temperature sensor

(6) Electronic Control Module (ECM)

(7) Suction control valve for the

high-pressure fuel pump

(9) Barometric pressure sensor

(10) Primary speed/timing sensor

(11) Oil pressure sensor

This document is printed from SPI². Not for RESALE

24

KENR9116-01

Troubleshooting Section

g02479258

Illustration 11

Close up views of sensor locations on the left side of a typical 1204E-E44 engine

(1) Coolant temperature sensor

(2) Intake manifold air temperature sensor

(3) Intake manifold pressure sensor

(4) Fuel rail pressure sensor

(5) Water-in-fuel switch

(8) Fuel temperature sensor

(6) Electronic Control Module (ECM)

(7) Suction control valve for the

high-pressure fuel pump

(9) Barometric pressure sensor

(10) Primary speed/timing sensor

(11) Oil pressure sensor

This document is printed from SPI². Not for RESALE

KENR9116-01

25

Troubleshooting Section

g02481176

Illustration 12

Sensor locations on the right side and the top of a typical 1204E-E44 engine

(12) NRS outlet pressure sensor

(13) NRS inlet pressure sensor

(14) NRS valve

(15) Nox Reduction System (NRS)

temperature sensor

(16) Wastegate regulator

(17) Secondary speed/timing sensor

(18) Exhaust back pressure valve (not

illustrated)

This document is printed from SPI². Not for RESALE

26

KENR9116-01

Troubleshooting Section

g02481197

Illustration 13

Close up views of sensor locations on the top of a typical 1204E-E44 engine

(12) NRS outlet pressure sensor

(13) NRS inlet pressure sensor

(14) NRS valve

(15) Nox Reduction System (NRS)

temperature sensor (not illustrated)

(16) Wastegate regulator

(17) Secondary speed/timing sensor (not

illustrated)

(18) Exhaust back pressure valve

This document is printed from SPI². Not for RESALE

KENR9116-01

27

Troubleshooting Section

1206E-E66 Engine

g02481236

Illustration 14

Sensor locations on the left side of a typical 1206E-E66 engine

(1) Fuel rail pressure sensor

(5) Suction control valve for the

high-pressure fuel pump

(6) Electronic Control Module (ECM)

(7) Fuel temperature sensor

(8) Barometric pressure sensor (not shown)

(9) Water-in-fuel switch

(10) Primary speed/timing sensor

(11) Oil pressure sensor

(2) Intake manifold pressure sensor

(3) Coolant temperature sensor

(4) Intake manifold air temperature sensor

This document is printed from SPI². Not for RESALE

28

KENR9116-01

Troubleshooting Section

g02481796

Illustration 15

Close up views of sensor locations on the left side of a typical 1206E-E66 engine

(1) Fuel rail pressure sensor

(5) Suction control valve for the

high-pressure fuel pump

(6) Electronic Control Module (ECM)

(7) Fuel temperature sensor

(8) Barometric pressure sensor

(9) Water-in-fuel switch

(10) Primary speed/timing sensor

(11) Oil pressure sensor

(2) Intake manifold pressure sensor

(3) Coolant temperature sensor

(4) Intake manifold air temperature sensor

This document is printed from SPI². Not for RESALE

KENR9116-01

29

Troubleshooting Section

g02483578

Illustration 16

Sensor locations on the right side and the top of a typical 1206E-E66 engine

(12) NRS outlet pressure sensor

(13) Wastegate regulator

(14) NRS valve

(15) NRS inlet pressure sensor

(16) Inlet temperature sensor for the NOx

Reduction System (NRS)

(17) Secondary speed/timing sensor

(18) Exhaust back pressure valve

This document is printed from SPI². Not for RESALE

30

KENR9116-01

Troubleshooting Section

g02395457

Illustration 17

Close up views of sensor locations on the right side and the top of a typical 1206E-E66 engine

(12) NRS outlet pressure sensor

(13) Wastegate regulator

(14) NRS valve

(15) NRS inlet pressure sensor

(16) Inlet temperature sensor for the NOx

Reduction System (NRS)

(17) Secondary speed/timing sensor

(18) Exhaust back pressure valve

This document is printed from SPI². Not for RESALE

KENR9116-01

31

Troubleshooting Section

Clean Emissions Module (CEM)

g02095035

Illustration 18

Sensors and components on a typical CEM

(1) Temperature probe for the inlet to the

DPF

(2) Inlet temperature sensor

(3) Aftertreatment identiﬁcation module

(4) Soot antennas

i04319697

Table 5

Engine Wiring Information

Color Codes for the Harness Wire

Color Code

Color

Color Code

Color

BK

BR

RD

OR

YL

Black

BU

PU

GY

WH

PK

Blue

Harness Wire Identiﬁcation

Brown

Red

Purple

Gray

Perkins identiﬁes all wires with 11 solid colors. The

circuit number is stamped on the wire at a 25 mm

(1 inch) spacing. Table 5 lists the wire colors and the

color codes.

Orange

Yellow

Green

White

Pink

GN

For example, a wire identiﬁcation of F730-OR on

the schematic would signify an orange wire with the

circuit number F730. F730-OR identiﬁes the power

supply for the oil pressure sensor.

Note: Always replace a harness wire with the same

gauge of wire and with the same color code.

This document is printed from SPI². Not for RESALE

32

KENR9116-01

Troubleshooting Section

Note: In the following diagrams, “Pxxx” signiﬁes a

plug and “Jxxx” signiﬁes a jack.

Schematic Diagrams

1204E-E44 Engine

g02101233

Illustration 19

Schematic diagram of the 1204E-E44 engine connections to the J2 connector on the ECM

This document is printed from SPI². Not for RESALE

KENR9116-01

33

Troubleshooting Section

1206E-E66 Engine

g02101353

Illustration 20

Schematic diagram of the 1206E-E66 engine connections to the J2 connector on the ECM

This document is printed from SPI². Not for RESALE

34

KENR9116-01

Troubleshooting Section

NOx Reduction System (NRS)

g02101473

Illustration 21

Schematic diagram of the NRS equipment for the 1204E-E44 and 1206E-E66 engines

Clean Emissions Module (CEM)

g02554116

Illustration 22

Schematic diagram of the Clean Emissions Module (CEM)

Wiring for the Application

This document is printed from SPI². Not for RESALE

KENR9116-01

35

Troubleshooting Section

g02488496

Illustration 23

Schematic Diagram for a Typical Application

This document is printed from SPI². Not for RESALE

36

KENR9116-01

Troubleshooting Section

i04021101

2. Position Tooling (A) around wire (2).

ECM Harness Connector

Terminals

Note: Make sure that the tool stays perpendicular to

the face of the connector (1).

3. Push the tool into the hole for the terminal. Gently

pull the wire in order to remove the terminal from

the rear of the connector (1).

The Electronic Control Module (ECM) uses

connectors that have 70 terminals to interface to the

wiring harness.

4. Remove the Tooling (A) from the wire.

Note: If a terminal must be replaced, part number

2900A016 must be used for 16 and 18 AWG wire.

Part number 28170024 must be used for 14 AWG

wire.

Terminal Insertion

1. Push the terminal into the rear of the connector (1)

until the terminal engages with the locking device.

2. Gently pull on the wire (2) in order to make sure

that the terminal is retained by the locking device.

3. Connect the connector to the ECM and then

tighten the retaining screw to a torque of 6 N·m

(53 lb in).

g01877659

Illustration 24

Layout of the Connector Pins (view from the rear)

Removal and Installation of the

Harness Connector Terminals

Terminal Removal

Table 6

Required Tools

Part

Tool

A

Part Description

Qty

Number

2900A019

Removal Tool (Red)

1

g01877813

Illustration 25

Removal Tool

1. Remove the connector from the ECM. Refer to

Disassembly and Assembly, “Electronic Control

Module - Remove and Install”.

This document is printed from SPI². Not for RESALE

KENR9116-01

37

Troubleshooting Section

Programming Parameters

Note: “Test ECM Mode” can only be activated if

the engine serial number has not already been

programmed during normal operation of the ECM.

If the engine serial number is programmed and the

ECM is not in “Test ECM Mode”, the ECM can never

be used as a test ECM.

i03939853

Programming Parameters

6. Use the “Copy Conﬁguration” feature on the

electronic service tool to program the test ECM.

The electronic service tool can be used to view

certain parameters that can affect the operation of the

engine. The electronic service tool can also be used

to change certain parameters. The parameters are

stored in the Electronic Control Module (ECM). Some

of the parameters are protected from unauthorized

changes by passwords. Parameters that can be

changed have a tattletale number. The tattletale

number is incremented whenever a parameter is

changed.

Note: If the “ECM Replacement” feature cannot be

used, program the test ECM with the values from the

“Customer Speciﬁed Parameters Worksheet” and the

values from the System Conﬁguration Parameters.

7. Program the engine serial number into the test

ECM.

Note: The “Test ECM Mode” must be activated

before the engine serial number is programmed into

the ECM.

i03939990

Test ECM Mode

8. Verify that the test ECM eliminates the fault.

When the “Test ECM Mode” is activated, an internal

timer sets a 24 hour clock. This clock will count down

only while the ECM is powered and the keyswitch

is in the ON position. After the ECM has counted

down the 24 hour period, the ECM will exit the “Test

ECM Mode”. The parameters and the engine serial

number will be set.

“Test ECM Mode” is a feature in the software that

can be used to help troubleshoot an engine that may

have a fault in the Electronic Control Module (ECM).

This feature allows a standard ECM to be used as a

test ECM. This feature eliminates the need to stock

a test ECM.

If the test ECM eliminates the fault, the engine can

be released while the “Test ECM Mode” is still active.

1. Search for the la, test ﬂash ﬁle for the engine.

Once an ECM has been activated in the “Test ECM

Mode”, the ECM will stay in the “Test ECM Mode”

until the timer times out. If the ECM is used as a test

ECM for more than one engine, the “Test ECM Mode”

must be reactivated. Anytime prior to the “Test ECM

Mode” timing out, the ECM can be reset to 24 hours.

Note: If a newer software version is available for the

engine, install the newest software on the suspect

ECM. If the new software does not eliminate the fault,

continue with this procedure.

2. Use the “Copy Conﬁguration” feature on the

electronic service tool to copy the parameters

from the suspect ECM.

i03898736

Factory Passwords

Note: If the “ECM Replacement” feature cannot

be used, record the programmed values into the

“Customer Speciﬁed Parameters Worksheet”. Also

record the system conﬁguration parameters.

NOTICE

3. Disconnect the suspect ECM. Temporarily connect

the test ECM to the engine. Do not mount the test

ECM on the engine.

Operating the engine with a ﬂash ﬁle not designed for

that engine will damage the engine. Be sure the ﬂash

ﬁle is correct for your engine.

4. Flash program the test ECM with the newest

software that is available.

Note: Factory passwords are provided only to

Perkins authorized distributors.

5. Start the “Test ECM Mode” on the electronic

service tool. Access the feature through the

“Service” menu. The electronic service tool will

display the status of the test ECM and the hours

that are remaining for the “Test ECM Mode”.

Factory passwords are required to perform each of

the following functions:

This document is printed from SPI². Not for RESALE

38

KENR9116-01

Troubleshooting Section

• Program a new Electronic Control Module

(ECM).

Note: You must have the engine serial number in

order to search for the part number of the ﬂash ﬁle.

When an ECM is replaced, the system conﬁguration

parameters must be programmed into the new

ECM. A new ECM will allow these parameters to

be programmed once without factory passwords.

After the initial programming, some parameters are

protected by factory passwords.

2. Connect the electronic service tool to the

diagnostic connector.

3. Turn the keyswitch to the ON position. Do not start

the engine.

4. Select “WinFlash” from the “Utilities” menu on the

• Rerate the engine.

electronic service tool.

Rerating may require changing the interlock code,

which is protected by factory passwords.

Note: If WinFlash will not communicate with the

ECM, refer to Troubleshooting, “Electronic Service

Tool Will Not Communicate with ECM”.

• Unlock parameters.

5. Flash program the ﬂash ﬁle into the ECM.

Factory passwords are required in order to

unlock certain system conﬁguration parameters.

Refer to Troubleshooting, “System Conﬁguration

Parameters”.

a. Select the engine ECM under the “Detected

ECMs”.

b. Press the “Browse” button in order to select

the part number of the ﬂash ﬁle that will be

programmed into the ECM.

• Clear engine events and certain diagnostic

codes.

Most engine events require factory passwords in

order to clear the code from ECM memory. Clear

these codes only when you are certain that the

fault has been corrected. For example, the 190-15

Engine Overspeed requires the use of factory

passwords in order to clear the code from ECM

memory.

c. When the correct ﬂash ﬁle is selected, press

the “Open” button.

d. Verify that the “File Values” match the

application. If the ﬁle values do not match the

application, search for the correct ﬂash ﬁle.

e. When the correct ﬂash ﬁle is selected, press

the “Begin Flash” button.

Since factory passwords contain alphabetic

characters, the electronic service tool must be

used to perform these functions. In order to obtain

factory passwords, proceed as if you already have

the password. If factory passwords are needed,

the electronic service tool will request the factory

passwords. The electronic service tool will display the

information that is required to obtain the passwords.

f. The electronic service tool will indicate when

the ﬂash programming has been successfully

completed.

6. Use the electronic service tool to check for

diagnostic code 631-2. If this diagnostic code is

active and the ﬂash ﬁle is not being installed in

order to change the engine rating, repeat this

procedure from 1. If this diagnostic code is active

and the ﬂash ﬁle is being installed in order to

change the engine rating, factory passwords must

be obtained.

i03898779

Flash Programming

7. Access the “Conﬁguration” screen under the

“Service” menu in order to determine the

parameters that require programming. Look under

the “Tattletale” column. All of the parameters

should have a tattletale of 1 or more. If a parameter

has a tattletale of 0, program that parameter.

Flash Programming – A method of loading a ﬂash

ﬁle into the Electronic Control Module (ECM)

The electronic service tool is utilized to ﬂash program

a ﬂash ﬁle into the ECM. The ﬂash programming

transfers the ﬂash ﬁle from the PC to the ECM.

8. Start the engine and check for proper operation.

Check that there are no active diagnostic codes.

Flash Programming a Flash File

1. Obtain the part number for the new ﬂash ﬁle.

Note: If you do not have the part number for the ﬂash

ﬁle, use PTMI on the Perkins web site.

This document is printed from SPI². Not for RESALE

KENR9116-01

39

Troubleshooting Section

“WinFlash” Error Messages

If any error messages are displayed during ﬂash

programming, click on the “Cancel” button in order

to stop the process. Access the “ECM Summary”

information through the “Information” menu. Ensure

that you are programming the correct ﬂash ﬁle for

your engine.

If a 630-2 diagnostic trouble code is displayed after

ﬂash programming, a required parameter is missing.

Program the missing parameter.

i03859293

g02132457

Injector Code - Calibrate

Illustration 27

Sequence for recording the injector code

The electronic service tool is used to load the injector

codes into the ECM.

Injector codes are codes that are 30 hexadecimal

characters in length that are supplied with each

injector. The code is on a plate on the top of the

injector and a card is also included in the packaging

for the injector. The code is used by the Electronic

Control Module (ECM) to balance the performance

of the injectors.

The injector codes must be loaded into the ECM if

any of the following conditions occur:

• An electronic unit injector is replaced.

• The ECM is replaced.

• Diagnostic code 268-2 is active.

• Electronic unit injectors are exchanged between

cylinders.

Note: Diagnostic code 268-2 will also become active

if the engine serial number, FLS or FTS are not

entered into the ECM.

If the ECM is replaced, the injector codes are

normally transferred to the new ECM as part of

the “Copy Conﬁguration” procedure. If the “Copy

Conﬁguration” procedure fails, the injector codes

must be loaded manually.

Installing Injector Codes

Note: The injector code is located on the electronic

unit injector.

g02132456

1. Record the injector code for each electronic unit

Illustration 26

injector.

Typical label with an injector code

2. Connect the electronic service tool to the

diagnostic connector. Refer to Troubleshooting,

“Electronic Service Tools”.

3. Turn the keyswitch to the ON position.

4. Select the following menu options on the electronic

service tool:

• Service

• Calibrations

This document is printed from SPI². Not for RESALE

40

KENR9116-01

Troubleshooting Section

Mode Selection Number

• Injector Trim Calibration

5. Select the appropriate cylinder.

6. Click on the “Change” button.

This parameter is a non-programmable parameter

that represents the number of possible combinations

of switch positions. This parameter is based on the

value that is programmed into the “Number of Switch

Inputs” parameter.

7. Input the applicable injector code that was

recorded in Test Step 1.

Mode Selection Switch Input 2 and

Mode Selection Switch Input 1

8. Click on the “OK” button.

The injector code is loaded into the ECM.

The number of these non-programmable parameters

that are visible depends on the value that is

programmed into the “Number of Switch Inputs”

parameter. “Open” signiﬁes that the switch is in the

OFF position. “Ground” signiﬁes that the switch is

in the ON position.

9. Repeat the procedure for each cylinder, as

required.

Exchanging Electronic Unit Injectors

Exchanging electronic unit injectors can help

determine if a combustion problem is in the electronic

unit injector or in the cylinder. If two electronic unit

injectors that are currently installed in the engine are

exchanged between cylinders, the injector codes

must also be exchanged. Press the “Exchange”

button at the bottom of the “Injector Trim Calibration”

screen on the electronic service tool. Select the two

electronic unit injectors that will be exchanged and

press the “OK” button. The tattletale for the electronic

unit injectors that were exchanged will increase by

one.

Rating Enabled

If “Yes” is selected on the drop-down menu, the

ECM is programmed to use the values in the “Rating

Number”, “Throttle 1 Droop Percentage”, “Throttle 2

Droop Percentage” and “TSC1 Droop Percentage”

for the given combination of switch positions.

Table 8

Values

Default

Factory Password

Yes

No

No

No

i04124470

Mode Switch Setup

High Idle Speed

The “High Idle Speed” is the maximum engine rpm.

The Mode Switches can be used to change the

performance characteristics of the engine. The

electronic service tool is used to program the

characteristics. Select the “Service” drop-down

menu and then select “Engine Operating Mode

Conﬁguration”. A maximum of two switches can be

used. “Switch 1” is connected to J1:62 Mode Switch

1. “Switch 2” is connected to J1:64 Mode Switch 2.

The other contact on both switches is connected to

J1:18 Switch Return.

Table 9

Minimum

Maximum

Default

1800 rpm

2800 rpm

2420 rpm

Rating Number

This parameter is the engine rating that is used by

the Electronic Control Module (ECM) for a given

combination of switch positions. There is a maximum

of four ratings in a ﬂash ﬁle.

Number of Switch Inputs

Table 10

This conﬁguration parameter is the total number

of switches that are used. The switches can be

individual switches or a multiple rotary switch.

Range

Default

Factory

Password

1 to the

maximum

1

No

Table 7

Range

Default

number of ratings

in the currently

installed Flash

File

0 to 2

0

This document is printed from SPI². Not for RESALE

KENR9116-01

41

Troubleshooting Section

Rated Speed (RPM)

Table 15

Range

Default

Factory

Password

This parameter represents the engine speed that is

selected when the mode switch or the mode switches

are in a particular position.

0 to 10 percent

5.0%

No

Table 11

TSC1 Droop Percentage

Range

Default

Factory

Password

This parameter represents the amount of droop that

is applied to the “Torque Speed Control 1(TSC1)”

input.

“Programmed

Low Idle” to

“Programmed

High Idle”

2100 rpm

No

Table 16

Range

Default

Factory

Engine High Idle Speed (RPM)

Password

0 to 10 percent

5.0%

No

This parameter represents a maximum of 112% of the

rated speed that is selected when the mode switch or

the mode switches are in a particular position.

i04105410

Throttle Setup

Table 12

Range

Default

Factory

Password

“1800 to 2800

rpm”

112% of rated

speed

No

There are two separate channels for throttle input.

The two channels can have any combination of a

digital throttle that uses a Pulse Width Modulated

(PWM) signal, an analog throttle or a multi-position

switched throttle.

Governor Type

This parameter represents the mode of operation of

the governor that is installed on the engine.

The Electronic Control Module (ECM) must be

programmed with the type of throttle input that is

being used in either position. From the menu, select

“Services”. On the “Services” screen, select “Throttle

Conﬁguration”. Select the type of throttle from the

following list:

Table 13

Range

Default

Factory

Password

“Min/Max speed

(rpm)” or “All

Speed”

All Speed

No

• No throttle

• Analog throttle

Throttle 1 Droop Percentage

• PWM throttle

This parameter represents the amount of droop that

is applied to the “Throttle 1” input.

• Multi-position throttle switch

The Electronic Control Module (ECM) must be

programmed for throttle arbitration. This parameter

determines which throttle input has priority. From the

menu, select “Services”. On the “Services” screen,

select “Throttle Arbitration”. Select the arbitration

method from the following list:

Table 14

Range

Default

Factory

Password

0 to 10 percent

5.0%

No

• Highest Wins

• Lowest Wins

• Manual Switch

Throttle 2 Droop Percentage

This parameter represents the amount of droop that

is applied to the “Throttle 2” input.

The default setting for throttle arbitration is “Highest

Wins”.

This document is printed from SPI². Not for RESALE

42

KENR9116-01

Troubleshooting Section

Lower Position Limit

This parameter is the minimum throttle percentage

that will be interpreted by the ECM as zero throttle.

This parameter is used with the value of initial lower

position limit to make an allowance for manufacturing

tolerances between different pedals.

Table 18

Range

Default

0 to 100%

10%

Initial Lower Position Limit

This parameter is the maximum throttle percentage

that will be interpreted by the ECM as zero throttle.

This parameter is used with the value of the lower

position limit to make an allowance for manufacturing

tolerances between different pedals.

g01785156

Illustration 28

Table 19

Typical Range of Throttle

Range

Default

(1) Lower Diagnostic Limit (Default=5)

(2) Lower Position Limit (Default=10)

0 to 100%

20%

(3) Initial Lower Position (Default=20)

(4) Idle Validation Minimum Off Threshold (Default=21)

(5) Idle Validation Maximum On Threshold (Default=25)

(6) Lower Dead Zone % (Default=8)

Idle Validation

(7) Upper Dead Zone % (Default=5)

(8) Initial Upper Position (Default=70)

(9) Upper Position Limit (Default=85)

All analog throttles and digital throttles can have an

idle validation switch. If this parameter is programmed

to “Yes”, the ECM will look for this switch input on pin

J1:22 for Idle Validation Switch 1 (IVS1) and J1:40

for Idle Validation Switch 2 (IVS2).

(10) Upper Diagnostic Limit (Default=95)

Analog throttles and digital throttles require additional

programming. If a multi-position switch is selected,

additional parameters must be programmed.

Refer to the Troubleshooting Guide, “Multiposition

Switch Setup”. If an analog throttle or a digital

throttle is selected, the following parameters can be

programmed into the ECM.

Table 20

Values

Default

No

Yes

No

Lower Diagnostic Limit

Idle Validation Minimum Off (Open)

Threshold

This parameter is the minimum throttle percentage

that should be detected by the ECM in normal

operation when the pedal is in the “off” position. A

value below this limit will generate a short circuit

diagnostic code. The range of this diagnostic

detection area is from 0 percent to the programmed

value for the lower position limit.

This parameter is the minimum throttle percentage

that will be detected by the ECM when the IVS is ON

(Closed).

If the ECM detects a throttle percentage below this

value with the idle validation switch OFF (Open),

a fault code will be generated and the engine will

remain at idle.

Table 17

Range

Default

0 to 100%

5%

Refer to Table 21 and Table 22.

This document is printed from SPI². Not for RESALE

KENR9116-01

43

Troubleshooting Section

Table 21

Throttle Position

Sensor (TPS)

Idle Validation Switch

(IVS)

Throttle Demand

Output

Fault Status

Raise IVS fault

No fault

Comment

TPS< IVS Min OFF

OFF

Minimum Position

Force throttle demand

to minimum

TPS< IVS Min OFF

ON

Throttle Position

Normal operation

Table 22

Range

Default

0 to 100%

21%

Idle Validation Maximum On

(Closed) Threshold

This parameter is the maximum throttle percentage

that will be detected by the ECM when the idle

validation switch (IVS) is OFF (Open) . When the idle

validation switch is OFF (Open) and the ECM detects

a signal that is higher than the programmed value for

IVS Max ON, the ECM will generate a fault code and

the engine will remain at idle.

Refer to Table 23 and Table 24.

Table 23

Throttle Position

Sensor (TPS)

Idle Validation Switch

(IVS)

Throttle Demand

Output

Fault Status

Comment

TPS> IVS Max ON

TPS< IVS Min Off

OFF

ON

Throttle Position

Minimum Position

No fault

Normal operation

Raise IVS fault

Force throttle demand

to minimum

Table 24

Table 26

Range

Default

Range

Default

0 to 100%

25%

0 to 100%

5%

Lower Dead Zone

Initial Upper Position Limit

This parameter is a throttle range above the initial

lower position limit before the engine will increase

in rpm.

This parameter is the minimum throttle percentage

that will be interpreted by the ECM as full throttle.

This parameter is used with the value of the upper

position limit to make an allowance for manufacturing

tolerances between different pedals.

Table 25

Range

Default

Table 27

0 to 100%

5%

Range

Default

0 to 100%

70%

Upper Dead Zone

This parameter is a throttle range that is below the

initial upper position limit that does not allow the

engine speed to increase.

Upper Position Limit

This parameter is the maximum throttle percentage

that will be interpreted by the ECM as full throttle. This

parameter is used with the value of the initial upper

position limit to make an allowance for manufacturing

tolerances between different pedals.

This document is printed from SPI². Not for RESALE

44

KENR9116-01

Troubleshooting Section

Table 28

Input 4, Input 3, Input 2, Input 1

Range

Default

The number of these non-programmable parameters

that are visible depends on the value that is

programmed into the “Number of Switch Inputs”

parameter. “Open” signiﬁes that the switch is in the

OFF position. “Ground” signiﬁes that the switch is

in the ON position.

0 to 100%

85%

Upper Diagnostic Limit

This parameter is the minimum throttle percentage

that is detected by the ECM in normal operation when

the pedal is in the maximum position. A value above

this limit will generate an open circuit diagnostic

code. The range of this diagnostic detection area is

from the programmed value of the upper position

limit to 100 percent.

Physical Position Enabled

If “Yes” is selected from the drop-down menu,

the ECM sets the engine rpm to the value that

is programmed into the “Engine Speed” for the

conﬁguration of the switches that is deﬁned for that

Physical Position.

Table 29

Range

Default

Table 31

0 to 100%

95%

Value

Default

No

No

Yes

i04105411

Multiposition Switch Setup

Logical Position

The Logical Position is the order that is required by

the user for a unique Physical Position.

Note: The multi-position throttle switch can only be

enabled if the optional PTO switches are not installed.

Table 32

The multi-position throttle switch is an optional

throttle input. A maximum of four switches can be

used. Four switches will allow a maximum of 16

speeds to be selected.

Range with Four

Switches

Default

1 to 16

1

Engine Speed (in RPM)

If an optional intermediate engine speed switch is

installed, the multi-position throttle switch can have a

maximum of three switches. Three switches will allow

a maximum of eight speeds to be selected.

The “Engine Speed” is the programmed engine rpm

for a particular position of the multi-position throttle

switch.

When the multi-position switch is selected as the

“Throttle Type” on the “Throttle Conﬁguration Screen”

of the electronic service tool, additional information

is required.

If the ECM detects a switch combination that

has been conﬁgured as “No”, a fault code will be

generated. In this situation, the ECM will ignore the

multi-position switch until the keyswitch is cycled

through OFF and ON.

Number of Switch Inputs

Table 33

This parameter is the total number of switches that

will be used. The switches may be individual switches

or a ganged rotary switch.

Range

Default

Programmed Low Idle to

Programmed High Idle

0

Table 30

Range

Default

1 to 4

0

Physical Position

This parameter is non-programmable. The parameter

is used to signify the position of the rotary switch.

This document is printed from SPI². Not for RESALE

KENR9116-01

45

Troubleshooting Section

Customer Speciﬁed

Speed Control

Parameters

Low Idle Speed

The “Low Idle Speed” is the minimum engine rpm.

i04317190

Customer Speciﬁed

Table 36

Parameters

Minimum

Maximum

Default

700 rpm

1200 rpm

750 rpm

Engine Conﬁguration Parameters

Customer speciﬁed parameters allow the engine to

be conﬁgured to the exact needs of the application.

Ether Solenoid Conﬁguration

Customer parameters may be changed repeatedly as

operational requirements change.

The ether solenoid conﬁguration deﬁnes the

presence of a solenoid for an ether starting aid.

Customer passwords are required in order to change

this parameter.

The following information is a brief description of

the customer speciﬁed parameters. The following

parameter values are included with the descriptions:

Table 37

• Minimum

• Maximum

• Default

Value

Default

Not Installed

Not Installed

Continuous Flow Solenoid

Engine Idle Shutdown

ECM Identiﬁcation Parameter

The Engine Idle Shutdown parameters deﬁne the

engine response when the keyswitch is turned to the

OFF position.

Equipment ID

“Equipment ID” is the identiﬁcation of the equipment

that is assigned by the customer. The “Equipment ID”

is only for reference by the customer. The “Equipment

ID” is not required by the Electronic Control Module

(ECM).

Minimum Ambient Air Temperature

Table 38

Value

Default

Table 34

0 to 29 Degrees C

0 Degrees C

Value

Default

Maximum Ambient Air Temperature

17 digits

The available characters

are dependent on the

service tool that is

being used.

Not programmed

Table 39

Value

Default

30 to 100 Degrees C

30 Degrees C

Engine Rating Parameter

Shutdown Enable Status

Rating Number

Table 40

The rating number is the selected rating within a

power rating family. The ﬂash ﬁle deﬁnes the power

rating family. The ﬂash ﬁle can contain one to four

ratings. The rating number deﬁnes the power rating

that is used within the power rating family.

Value

Default

Enabled

Disabled

Disabled

Table 35

Minimum

Maximum

Default

1

4

1

This document is printed from SPI². Not for RESALE

46

KENR9116-01

Troubleshooting Section

Shutdown Delay Time

• “Throttle Lock Increment Speed Ramp Rate”

Table 41

• “Throttle Lock Engine Set Speed Increment”

Value

Default

Table 45

1 to 60 minutes

5 minutes

Value

Default

Not Installed

Installed

Ambient Temperature Override Enable

Status

Not Installed

PTO Mode

Table 42

Value

Default

PTO mode can be conﬁgured to operate in either

Set/Resume mode or Ramp up/Ramp down mode.

Set/Resume mode allows the engine speed to be

controlled by the operator through switch inputs.

This mode allows two speciﬁc speeds to be set

and stored in the ECM. A speed can be selected

or the previously selected speed can be resumed.

Adjustments in engine speed can then be made via

the raise and lower switch inputs. Ramp up/Ramp

down mode only allows the engine speed to be raised

or lowered via switch inputs at a desired ramp rate.

The “Set” and “Resume” functions are disabled.

Enabled

Disabled

Disabled

Air Shutoff

Air Shutoff

The Air Shutoff parameter deﬁnes whether an air

shutoff valve is installed in the air inlet for the engine.

Table 43

Table 46

Value

Default

Value

Default

Enabled

Disabled

Disabled

Ramp Up/Ramp Down

Set/Resume

Set/Resume

Multiple Engines on J1939

Throttle Lock Engine Set Speed 1

Engine Location

The “Throttle Lock Engine Set Speed 1” parameter is

one of the engine speeds that can be selected in the

PTO Set/Resume mode.

In a situation where multiple engines communicate on

one J1939 channel, the Engine Location parameter

deﬁnes the identity of each engine in the set.

Table 47

Minimum

Maximum

Default

Table 44

Value

Default

Low idle speed

Rated speed

700

Engine #1

Engine #2

Engine #3

Engine #4

Engine #5

Throttle Lock Engine Set Speed 2

Engine #1

The “Throttle Lock Engine Set Speed 1” parameter is

one of the engine speeds that can be selected in the

PTO Set/Resume mode.

PTO and Throttle Lock Parameters

Table 48

Minimum

Maximum

Default

Throttle Lock Feature Installation Status

Low idle speed

Rated speed

700

Note: PTO and a multi-position throttle switch cannot

be installed at the same time.

Throttle Lock Increment Speed Ramp

Rate

The “Throttle Lock Feature Installation Status” is

used to turn on the throttle lock features. When this

parameter is changed to “Installed”, the following

parameters are active and the parameters can be

programmed.

The “Throttle Lock Increment Speed Ramp Rate”

parameter is the rate of engine acceleration when the

PTO switch is held in the ACCELERATE position. If

this parameter is set to “0”, the feature is turned off.

• “PTO engine Speed Setting”

This document is printed from SPI². Not for RESALE

KENR9116-01

47

Troubleshooting Section

Table 49

Table 53

Minimum

0 rpm/sec

Maximum

Default

Value

Default

600 rpm/sec

400 rpm/sec

Disabled

Enabled

Enabled

Throttle Lock Decrement Speed Ramp

Rate

Monitoring Mode Derates

The “Monitoring Mode Derates” parameter controls

the amount of derate that is associated with the

engine monitoring feature. When this feature is

enabled and a diagnostic code with an appropriate

FMI is detected, the engine will be derated.

The “Throttle Lock Decrement Speed Ramp Rate”

parameter is the rate of engine deceleration when

the PTO switch is held in the DECELERATE position.

If this parameter is set to “0”, the feature is turned off.

Table 50

Table 54

Minimum

Maximum

Default

Value

Default

0 rpm/sec

600 rpm/sec

400 rpm/sec

Disabled

Enabled

Enabled

Throttle Lock Engine Set Speed

Increment

Limp Home Desired Engine Speed

The “Throttle Lock Engine Set Speed Increment”

parameter controls the increase in engine speed

when the PTO switch is brieﬂy operated to

ACCELERATE. If this parameter is set to “0”, the

feature is turned off.

The “Limp Home Desired Engine Speed” parameter

is the maximum speed of the engine when the engine

has been derated.

Table 55

Minimum

Maximum

Default

Table 51

700 rpm

1800 rpm

1200 rpm

Minimum

Maximum

Default

0 rpm

200 rpm

10 rpm

Engine Acceleration Rate

Throttle Lock Engine Set Speed

Decrement

The “Engine Acceleration Rate” parameter is the

acceleration rate for the engine under normal

operating conditions. A setting of “0” disables this

function.

The “Throttle Lock Engine Set Speed Decrement”

parameter controls the decrease in engine speed

when the PTO switch is brieﬂy operated to

DECELERATE. If this parameter is set to “0”, the

feature is turned off.

Table 56

Minimum

Maximum

Default

0 rpm

65503 rpm/sec

0 rpm/sec

Table 52

Minimum

Maximum

Default

Engine Speed Decelerating Ramp Rate

0 rpm

200 rpm

10 rpm

The “Engine Speed Decelerating Ramp Rate”

parameter is the deceleration ramp rate for the

engine under normal operating conditions. A setting

of “0” disables this function.

Miscellaneous

Monitoring Mode Shutdowns

Table 57

Minimum

Maximum

Default

The “Monitoring Mode Shutdowns” parameter

controls the shutdown feature that is associated with

the engine monitoring feature. When this feature is

enabled and a diagnostic code with a “-31” sufﬁx is

detected, the engine will be shut down.

0 rpm

65503 rpm/sec

0 rpm/sec

Intermediate Engine Speed

The “Intermediate Engine Speed” is a selectable

engine speed that is between the low idle speed and

the high engine speed. This parameter is disabled

when the value is set to 0 rpm.

This document is printed from SPI². Not for RESALE

免費熱線
400-100-8969???15088860848

機組銷售
0574-26871589? 15267810868

配件銷售
0574-26886646? 15706865167

維修熱線
0574-26871569 18658287286

手機端

微信公眾號

在線客服

配件咨詢

咨詢一號
咨詢二號
咨詢三號
咨詢四號

技術支持

售后人員

自拍偷区色综合,日韩av毛片网站,九七人妻碰碰视频,日韩幕无线码一区中文,天堂av网站大全,成人区人妻精品一区二区18,GV无码免费无禁网站,国产亚洲精品精品一区二区,熟女亚洲精品,波多野精品一区二区三区色情,边吃奶亚洲一区二区

日本网址免费中文| 亚洲欧美日韩在线不卡| 99久久综合精品五月天人人| 亚洲精品高潮久久久久久久久| 岛国av免费电影在线播放| 午夜爽爽爽男女免费观看一区二区 | 两个人免费观看日本完整视频| 亚洲激情av免费电影| 午在线亚洲男人午在线| 野外国产精品久久免费9|久久 | 2021国产成人精品视频| 久久免费特级黄片| 欧美va日韩va亚洲va| 漂亮人妻侵犯中文字幕日本一级| 色播久久人人爽久久人人| 免费日韩av影视网站| 日韩揉捏奶头高潮不断视频| 不卡的av影片| av亚洲aⅴ久久精品| 人成欧美视频在线| 国产精品九九久久_久久国产| 国产一区二区三区播放视频| 男人日女人视频免费| 亚洲日本女人午夜影院| 欧美变态另类bdsm刘玥| 亚洲另类欧美久久久| 男女免费视频国产| 国产精品成人1区二区免费| 亚洲av制服师生一区二区三区| 在线综合亚洲欧美国产| 日韩亚洲欧美中文| 国产不卡在线一区二区三区| 日韩在线精品人妻| 9420高清完整版在线观看免费| 欧美日韩中文国产一区发| 成人av在线观看高清国产| 91人妻熟女系列| 欧美一级日韩不卡播放免费| 91成人福利影院| 成年黄页网站大全免费看| 99视频精品在线看.| 免费av大蜜桃| 超碰成人人人在做人人爽| 国产免费的打野战视频| 精品久久久久久99| 亚洲精品蜜臀av久久久| 亚洲中文字幕欧美精品| 国内a级黄色毛片| 成人一区二区三区高清小视频| 爽到高潮漏水大喷无码视频| 国产在线欧美一区二区三区| 欧美少妇被猛烈插入视频| 久久久久网色| 欧美最新一区另类| 高清黄色片网址| 熟女中文另类亚洲| 热国产热有码| 要看国产av| 美女脱内衣禁止18以下尤物| 欧美大片在线观看一区二区| 老司机精品视频免费入口| 欧美图片区小说区视频区| 人人妻人人澡人人爽人人极品| a级毛片高清视频免费就看| 啦啦啦啦视频在线| 91麻豆国产语对白在线观看| 久久久久人妻精品一区二区三区 | 国产亚洲欧美精品永久| 一个人看www的高清视频| aa级毛片免费播放| 2021精品一区二区三区| 成人免费视频播放| 久久久一区二区三区| 久久国产精品一国产精品| 内谢国产内射夫妻免费视频| 在线看片免费人成视频a区| 男人扒开添女人下部全视频| 哪个播放器儿童片免费的多| 日本av视频观看| 日韩精选在线观看不卡视频免费| 男人天堂久久av噜噜| 狠人色综合网亚洲| 亚洲精品国产片av| av大片不卡| 欧美日韩一级特黄大片| 鞭打虐乳跪爬sm羞辱视频| 狠狠躁夜夜躁人人爽天天天天| 日日人人妻人人澡人人爽欧美| 欧美日韩av视频一区| 日本最新不卡免费一区二区| 国产在线观看男天堂| 成年女人免费视频网站| 成年黄色视频在线播放| 亚洲在线观影| 国产精品国产高清国产av| y1111111少妇免费观看| 无码人妻久久一区二区三区免费| 美腿丝袜亚洲欧美综合| 最近2019中文字幕大全视频1| 亚洲天堂网最新版| 久久久久精品人妻av中出| 美女脱光免费网站| 亚洲国语对白在线精品一区在线| 亚洲欧洲日韩综合| 黑人ⅹxx亚洲人一区二区| 91久久精品国产一区二区三区| 丰满成熟的女人片aaa久久久| 国产乱理伦片在线观看夜| 亚洲综合一区自偷自拍| 国产精品综合久久久久久久免费 | 搡老女人老妇老熟女hd| 人妻少妇精品偷人视频| 国产亚洲av人片在线观看成人| 人人狠狠综合久久亚洲咪咪色| 国产精品久久久久久久福利| 国产精品成人久久网| 国产精品人妻一区一区三区| 在线播放的a网站| 色哟哟国产成人精品免费| 亚洲天天久久中文字幕| 后入人妻在线视频| 亚洲精品国产乱码久久久久久| 日韩高清人妻一区二区三区不卡的av | 亚洲欧美一区二区激情| 欧美日韩一区二区视频免费观看| 亚洲+欧洲+日产+韩国精品| 男桶女免费60分钟视频| 一级做a爰片久久毛片69| 建设银行对私可以办卡吗| 偷窥妇女BBW| 久久久成年人免费电影| 高跟凉鞋肉色丝袜| 精品视频一区二区乱码国产| 1080p超清在线观看影视网站| 欧美人与禽ZOZ0性伦交| 毛片av免费| 小SAO货夹得好紧太爽了视频| 久久精品国产亚洲蜜臀av| 日韩免费在线观看av| 久久国产精品成人免费网站| 秋霞在线观看av.www| 欧美丝袜足j| 午夜诱惑老司机视频| 在线观看A片的视频网站| 欧美亚洲国产日韩精品播放| 成人av看看永久免费发布| 亚洲av二区三区四区| 久久久欧美国产精品人妻| 91av看片在线| 久久久久精品av毛片| 午夜DJ高清视频观看播放| 插逼摸胸骚货视频| 少妇被粗大的猛烈进出视频| 日本一级a爰片| gogo大胆午夜人体视频网| 92福利自产国产精品视频| 国产精品三级久久久久久久久| 18禁男人添女人无遮挡| 精品国产免费观看| 午夜伦4480YY私人影院久久| 91av精品麻豆视频| 99v久久人妻| 女人18片毛片60分钟免费观看| 国产高清一区二区三区直播| 成人亚洲精品久久久久软件| mm131美女视频毛片| 娇妻被朋友粗大猛烈进出高潮视频| 一本久久中文字幕| 午夜福利网站1000一区二区三区| 国产精品久久av一区| 亚洲欧美少妇熟女| 亚洲精品国产一级c片| 在线观看午夜亚洲福利| 7777精品久久久久久| 亚洲欧美国产日韩动漫 | 亚洲av男人的天堂日韩| 久久精品三级电影视频| 亚洲精品色青久久久久久久 | 99久久嫩草影院| 欧美成人免费午夜福利片| 午夜福利国产精品久久婷婷69| 波多野结衣一区二区三区视频| 99精品久久久久久琪琪| 91九色亚洲精品| 中文字幕好看男人天堂网| 一边摸一边桶一边脱免费| 无码A片免费种子网址| 人妻一区二区三区蜜桃| 精品熟女少妇av免费看| 亚洲av秘av| 日韩精品在线久av观看| 晚上进了女小娟的身体| 寂寞影院一区二区三区| 亚洲色图男人天堂中文字幕| 午夜福利黄片免费看| 狠狠躁夜夜躁人人爽天天天天| 最新MATURE熟女成熟丰满| 国产性色一区二区三区av| wwwxxx老熟女| 亚洲精品网站的| 亚洲日本成人高清视频| 久久综合亚洲色一区二区三区| 国产精品不卡一区二区三区av| 国内免费一级毛片| 丰满岳乱妇高清视频在线观看| 辽宁熟女高潮狂叫视频| 国产亚洲精品超碰热| 扒开双腿疯狂插入爽爽爽视频| 久久久久中文字幕免费a| 久久久久久久大尺度免费视频| 91精品国产熟女| 最近2019中文字幕免费视频大全| 亚洲欧美日韩精品二区| 女人精品久久久久毛片| 成年黄色视频在线播放| 午夜福利视频亚洲一区| 美女被c到高潮免费视频| 熟妇少妇精品综合| 两个人的bd视频全免费| 国产精品扒开腿做爽爽爽视频软件| 搞人妻少妇精品视频| 18禁国产精品久久久久久久久久 | 97国语自产视频在线免费观看| 中文字幕日韩高清一区| 好大好深我高潮了| 久久av蜜桃一区二区三区| 亚洲av天堂久久精品| 婷婷亚洲伊人| 娇小可爱学生videos15| 初学生毛片国产av下载| 久久9精品影院| 欧美一区二区成人影院| 亚洲综合色区另类小说| 午夜久久久久久久99精品婷婷| 国产精品视频永久免费观看| 丁香在线视频观看| aa一级片在线观看| 真人作爱90分钟免费看视频| 最近最好看的中文字幕2019| 毛片a级放荡的护士久久| 夜夜夜夜猛噜噜噜噜噜| 久久影院精品久久| 精品人妻小视频| JAPAN强要VIDEOD警妞| 久久精品一区亚洲| 亚洲精品国产精品久久9| 亚洲性无码AV在线DVD| 国产午夜视频在线免费观看| 一级生活片九九视频免费看| 国产精品你懂的在线播放| 在线未删减欧美一区二区中文| 亚洲春色少妇熟女小说| 18禁裸露啪啪网站免费| 99久久亚洲精品蜜臀| 国产a乱精品一区| 狠狠久av北条麻妃xxx| 精品亚洲av乱码国产毛片| 成年女人20级毛片毛片免费| 丝袜美腿一区二区三区| 欧美与性动交α欧美精品| 日日摸夜夜添夜夜添爽视频| 秋霞久久亚洲精品成人| 欧美成人午夜免费影视| 久久精品四虎av| 毛片一级片免费看久久久久| 日本欧美三级一二三区| 狠狠综合久久久久综合网站| 国产欧美日韩一线| 老熟女一区二区免费| 国产伦精品一区二区三免.费| 美女色骚噜噜| 亚洲最大成网人站亚洲ADC| 黄色床上戏免费看| 立即播放在线一级黄色视频| 久久久久久免费观看全是精品| 久久久久久久人妻熟女| 精品少妇人妻久久免费| 亚洲+欧洲+日产+韩国精品| 国产91内射毛片| 亚洲日本乱码很鲁欧美乱码| 在线观看国产精品av| 亚洲最大av一区二区三区| 巨乳av免费在线观看| 亚洲精品一区国产二区三区四区 | 伊人热热久久原色播放WWW| 国产精品午夜a毛片一级| 亚洲成人鲁丝片| 亚洲精品亚洲人av| 男人舔女人下半身高潮视频| 绯色av一本一道道久久精品| 97超碰大香蕉| 精品亚洲在线播放| av中文字幕第一区| 成人激情视频免费在线播放| 亚洲成人av在线播放网站| 国产做a爱片久久| 综合色亚洲区| 第一次破女处流血视频| 精品国产福利导航| 俄罗斯老熟妇色XXXX| 国产影片一区二区| 亚洲精品午夜久久久久久久久中文| 国产成人区一区二区三区| y1111111少妇免费观看| 美女视频全是免费| 国产成人在线播放一区二区| 亚洲av一影院| 激情综合五月丁香亚洲| 欧美福利一区二区精品视频| 嗯~~~爽~~~~再快点| 亚洲国产成人精品女人aaa| 久久大香香蕉国产| 美女视频亚洲免费| 最近中文字幕免费高清大全| 男女羞羞视频网页| 欧美日韩手机不卡在线| 国产91对白叫床清晰播放| 免费在线看黄色的网站 | 亚洲欧美码一区| 日本人与黑人牲交高潮| 区二区三区国产精华液| 亚洲午夜福利精品| 特别色的网站在线观看| 精品国产精品三级国产高清| AV午夜福利一片免费看久久 | 精品人人妻人人澡人人爽牛牛| 91精品国产一区二区三区| 啪啪国产精品亚洲欧美一区麻豆| 亚洲精品国产精品久久久| 嗯啊嗯啊黄色在线观看视频网站 | 国产毛片啊久久久久| 欧洲免费无线码在线观看| 亚洲精品加勒比av| 亚洲无线码高清在线观看| 亚洲最大一区av| 已有111111少妇影院| 三级毛片的视频播放的| 美女扒开内裤无遮挡18禁| 久久久久久久精品成人热蜜柚| 野花韩国高清完整版在线观看| 成人国产麻豆网| 强奷喂奶人妻黑人| 亚洲av中文无字幕| 久久夜色精品久久噜噜亚| 男人大片在线观看| 午夜福利久久日av| 97视频在线观看网站| 又黄又硬又爽的视频| 国产日韩AV免费无码一区二区| 亚洲av秘av| 内射白嫩的小少妇33p| 国产毛片久久久久久高清美女| 国产一区二区三区av免费| a亚洲精品国产av电影在线观看| 国产成人精品视频| 欧美淫根插插插一区二区三区 | 欧美色一区二区三区四区| 高清黄色片网址| 91人人妻人人澡人人爽人人| 国产精品区久久一区二区| 日韩国产欧美精品一区二区三区| 亚洲精品少妇30P| 99精国产麻豆久久婷婷| 国产午夜电影在线电影| 日韩精品国产自在欧美| 午夜精品伦理电影| 免费在线成人午夜视频| 欧美日韩视频一区二区在线| 欧美三级精品视频在线观看视频| 久久久久久久久99精只大国产| 老司机在线精品视频播放| 国产免费一级a男人的天堂| 毛片在线一区二区三区| 两个人日本高清| 亚洲精品国产a久久久| 伊人久久精品无码二区麻豆| 国产成人秘史在线播放 | 亚洲娇小与黑人巨大交| 亚洲区国产一区二区| 亚洲大型综合色网| 人禽交欧美网站| 熟女熟妇伦51788| 日本精品久久久久精品三级一| 日本中文字幕亚洲乱码| 精品视频中文字幕在线观看| 精品亚洲av乱码国产毛片| 免费A片在线网站大全高清 | 久久久久久久大尺度免费视频| 麻豆大尺度激情视频在线观看| 高清中文字幕亚洲| 久久9a精品国产麻豆婷婷| 99v久久人妻| 日韩欧美亚洲一区66| 国产精品久久久久久av下载网址 | 国产视频乱来| 女高中生高潮娇喘喷水视频| 黑人狂插视频| 久久国产亚洲av麻豆专区| aa永久免费网站| 看黄色看黄色| 日本免费在线ww| 看真人视频一一级毛片免费| 自拍偷自拍亚洲精品老妇| 伸进内裤里揉捏视频免费| 被黑人连续猛烈高潮视频| 成人无遮挡在线看| 被吃奶跟添下面特舒服细节| 成人午夜视频网址| 丁香六月久草| 最好的美女福利视频网| 国产传媒天美一区二区三区| 成a人片国产精品| 中文字幕人妻熟女日韩精品 | 国产偷国产偷亚洲高清日韩| 国产不卡免费69av| 91成人国产综合久久精品| 体育生18cm.大屌狂操卫校白嫩学生妹直接操 | 看免费黄色特级毛片| 久久播国产精品| 亚洲黄色在线免费播放| 国产精品久久久久毛片真精品| 91网站入口永久在线观看| 在医院被医生强到爽| 日韩激情熟女| 欧美性事xxxx| 亚洲精品少妇30P| www,sex,xxx| 中文字幕伊人久久亚洲| 宅男视频老司机| 中国大屁股XXXX| 色爱av一区二区三区人妻| 女生黄频黄色视频免费观看| 有码中文字幕a| 闺蜜把我腿打开用黄瓜自慰| 人妻毛片免费观看| 成人国产色综合| 93国产精品久久久久久| 噜噜影院一区二区| 亚洲精品加勒比av| 欧美淫根插插插一区二区三区 | 人妻体验按摩调情BD| 午夜激情久久久久| 97久久热精品| 人人妻人人澡人人爽xxx| 三级a黄色毛片| 欧美牲交A欧美牲交AⅤ电影| av高清亚洲一区| 亚洲熟女激情| 人人狠狠综合88亚洲| 亚洲精品国产有码| 很黄很黄的女同性A片| 在线天天成人av在线| 亚洲熟女毛片儿| 日韩欧美激情国产精品| 客厅乱H伦亲女| 在线视频福利专区| 强奷绝色年轻女教师| 日本边摸边吃奶边做gif视频| 国产avxxx| 人妻少妇久久毛片| 国产呦萝小初合集密码| 无码AⅤ免费中文字幕久久| 忘忧草蜜芽188| 国产成人一区二区欧美视频| 一区二区三区午夜精品| 久久精品影院| www.嫩草影院.com| 久久精品国产亚洲av高另类| 日韩美高清视频| 日日夜夜操福利| 男人天堂大片| 毛片av日韩| 彩虹男孩短剧免费观看高清| 最近2019中文字幕免费视频大全| 亚洲精品在线99| 日韩欧美一精品| 久久久久影院毛片免费观看| 国产极品小粉嫩| 97人人人妻人人澡人人爽| 午夜精品成人在线观看视频| 18禁男人添女人无遮挡| 久久婷婷国产麻豆91天堂 | 亚洲日本女人午夜影院| 99国产精品久久久久久另类| 啪啪啪李毅动态图| 91网站入口永久在线观看| 在线视频亚洲成人| 新婚少妇毛茸茸的性| 两个人高清视频免费看| 成人区人妻精品一区二区三区| 天天摸夜夜添逼| 色护士亚洲精品影院手机版| 久久夜色精品久久噜噜亚| 7777精品久久久久久| 黄色av女优| 亚欧美无遮挡HD高清在线视频| www.毛片免费视频| 欧美精品一区二区免费开放| 欧美成人免费全部网站| 亚洲一区二区av免费观看入口| 一级毛片a级毛片免费看| 猫咪香蕉av| 黄色大片视频在线观看不卡| 久久成人黄片| 人妻视频一区二区| 日本高清www色视频总站免费| 国产精品欧美日韩电影| 午夜男人的天堂网| 国产精品va在线播放我和闺蜜| 成人女子免费视频| 国产又黄又涩视频| 亚洲三级香港三级久久| 亚洲免费午夜电影| 97国产成人精品视频免费 | 特黄三级毛片| 免费一级a级高清毛片人妻6| 黄色激情美女视频网址| 国产丝袜制服诱惑av| 欧美午夜夫妻性生活视频| 一级毛片我不卡| 亚洲国产精品8x| 噜噜插内射精品| 日本最新av免费观看| 一本久久综合精品| 久久九九99这里只有精品| 日韩美一级大片| 国产激情一区二区三区在线播放| 强壮公弄得我次次高潮| 国产一级^老妇内射| 韩国午夜理伦三级好看| 人妻无码AV中文系列久久免费| 亚洲AV日韩AV高潮潮喷无码| 小SAO货水好多真紧H视频| 免费精品国产自在| 奇米影视777四色狠狠| 国产永久免费视频| JAVA性无码HD| 粗长巨龙挺进人妻后臀| 国产99视频免费精品| 久久精品女人av天堂免费av| 日韩欧美一区二区三区在线 | 午夜av精品一区二区三区| AV免费不卡国产观看| 高潮呻吟国产在线播放| 精品久久久久久国产里采 | 女的被弄到高潮喷水抽搐| 激情综合五月丁香亚洲| 黑人巨茎大战俄罗斯美女| 亚洲中文字幕永久在线不卡| 色婷婷久久综合中文久久一本| 少妇被粗大的猛进出| 午夜男女大片免费观看18禁片| 色综合图片区小说区| 东北老太婆BBB| 日韩麻豆av中文字幕在线观看| 欧美日韩视频在线观看免费网址| 美女被别人操高潮的视频免费| 女人性高朝床叫视频尖叫声| 日本精品成人h无遮挡动漫| GOGO专业大尺度亚洲高清人体| 久久精品国产91久久麻豆| bt天堂新版中文在线| 999精品视频国产| 少妇又粗又猛又爽又黄的视频| 动漫av区网站| 男人躁女人到高潮av| 麻豆岛国国产精品| 国产不卡亚洲av午夜网站| 婷婷丁香网五月| 久久国产精品亚洲av成人| 欧美日韩亚洲v| 亚洲另类激情专区小说图片| 啪啪在浴室边摸边吃奶边做大全 | 久久人人爽国产| 国产日韩av高清在线不卡| 四个闺蜜把我弄高潮了| 久久99精品久久久久久牛牛影视| 无需下载免费观看国产黄片| 尿液呈红黄色是怎么回事| 亚洲成人av麻豆av| 一区二区中文字幕人妻寝取| 亚洲第一毛片av| а√天堂资源地址在线官网下载| 亚洲中文字幕精品久久| 特a级黄色毛片| av在线不卡观看一本| 国产色在线一区| 日本入室强伦姧BD在线观看| 美女扒开内裤让我爽| 欧美成年午夜免费全部| 男女视频福利网| 亚洲a在线视频免费观看| 午夜激情在线免费观看| 中国女人大白屁股ASS| 精品国产毛片在线看一区| 自拍偷自拍亚洲精品老妇| 亚洲日韩中文字幕无码专区| 18禁网站免费看| 欧美一区国产一区激情| 亚洲人精品天堂| 一级做a爰片久久毛片美女图| 国产亚洲脚酸久久av| 亚洲AV无码国产在丝袜线观看 | 久久人人妻人人做| 亚洲欧美综合一区在线观看| 被弄到高潮喷水呻吟在线观看| 丰满亚洲大尺度无码无码专线| 俄罗斯XX性幻女18| 97在线观看视频在线久| 99re66久久在热青草| 成人影院亚洲天堂| 日韩成人在线影片| 又黄又爽的视频免费99| a级毛片毛片毛片| 国产老熟女aⅴ| 三级伦理电视剧| 欧美国产日韩一二三区| 人妻不伦在线观看| a中文天堂在线官网| 亚洲精品久久国产精品| 国产伦精品一区二区三区| 免费毛片a级观看| 欧美日韩一级特黄大片| 色SE01短视频永久网站| 免费播放成年人视频| 亚洲欧美精品综合一区二区三区 | 国产aⅴ亚洲aⅴ欧州av| 一级做a爰片久久毛片国语| 国产欧美日韩高清不卡| 图片区小说视频区| 欧美精品一区二区精油| 又粗又长又大又硬又爽的少妇毛片| 中文有码人妻制服| 香蕉国产在线观看| 日日射夜夜猛干| 亚洲高清国产拍精品| 久久精品国产99国产精品小说| 午夜国产亚洲精品一区| 国产色老太色老太视频在线| 放荡爆乳女教师电影在线观看| 一级做a爰片久久毛片69| 人人妻人人看人人澡| 国产欧美精品一区电影在线| 一女三男做2爱A片| 全黄男人和女人视频| 中文字幕第一页久久| 亚洲高清视频不卡| 波多野结衣办公室33分钟激情| 日韩欧美精品在线第一页| 久久精品天天中文字幕人妻乱要| 夸克免费电影大全播放器| 亚洲综合一区二区精品久久| 美女黄是视频免费看| 国产午夜真人理论片| 亚洲av在线高清观看| 国产日韩AV免费无码一区二区| 日本激情电影一区二区| 久久ye,这里只有精品| 日日摸夜夜添夜夜添毛片精选 | 欧美色网站在线观看视频| 国产aⅴ一区二区三区精华液| 最近免费高清视频观看日本| 亚洲精品中文字幕三区| 久久青青狼人影院| 成年女人视频免费| 在线久久av| 亚洲中文无码人A∨在线观看| 色婷婷久综合久久国产午夜精品| 99久久精品国产av麻豆| 偷拍亚洲偷自拍| 日韩精品一级黄色| 国产三区精品视频观看| 久久久久久免费女人体| 婷婷色亚洲av| 国产精品av专区| 日本色图影院| BBBBBXXXXX精品| 美女视频黄频大全免费的| 久久精品国产专区| 国产高清真实破学生处| 下个黄色毛片免费的| 国产精品午夜性视频入口| 美女双飞高潮直喷水在线播放 | av大香蕉在线| Japan Video XXX Sorry| 亚洲不卡av网站| 国产精品亚洲怡红院使用方法| 日本久久久久久中文字幕1| 国产精品偷在线观看 | 欧美日韩一区二区乱码| 91嫩草在线播放| 漂亮人妻洗澡被公强| 成人av看看永久免费发布| 中出人妻视频一区二区| 色综合图片区小说区| 一级a一级a爰片免费久久久| 国产综合野战| 韩国理论片在线观看2828| 久久国产精品影院| 国内老熟妇VIDEOHD| 就去吻亚洲成人网| 国产精品扒开腿做爽爽视频| 人禽杂交18禁网站| 人妻激情视频一区二区三区| AV区无码字幕中文色| 午夜福利z在线| 亚洲视频免费永久| 黑人与牛交ZOZOZO| 国产精品视频卡一区二区三区| 欧美日韩在线大片| 久久精品一区亚洲| 黑人狂插视频| 亚洲欧洲日产精品| 日韩人妻一区二区有码| 亚洲精品高清自拍| 人妻碰碰久久| 日本高清二区视频久二区| 又粗又硬又爽免费毛片视频| 黄色成人天堂| 五月天婷五月天综合网| av电影中文网址| 男人午夜福利在线观看| 日本一区二区三区精品电影| 蜜桃av高潮抽搐| 先锋77xfplay色资源网站| 99久久久区一区二区三| 久久久国产精品久久久久| 免费日韩av影视网站| 国产精品一区二区三区a| 日本动漫十八禁黄无遮挡吸乳| 久久综合久久自在自线精品自| 亚洲av大片在线播放| 日韩免费av电影网址| 男人日女人视频免费| 性生大片免费观看668| 男人天堂久久网站| 欧美久久久久久久毛片| 99久久精品国产亚洲av葫芦| 秋霞精品一区二区三区电影| 国产精品久久久久久久久久不蜜月| a级毛片免费在线看| 97精品国产高清一区二区三区| 日本av视频免费观看| 亚洲欧洲自拍拍偷午夜色无码| 国产视频内射| 人人揉揉揉揉揉日日| 国产精品视频大全免费观看| 精品国产乱码aaa一区二区| 久久九九午夜福利| 青春草在线视频网址观看| 久久国产精品婷婷一区二区| 手机av亚洲| 国产麻豆久久久久久久精品| 一区二区日韩人妻| 亚洲66av| 欧美大尺度无遮挡A片| 91久久精品www人人做人人爽| 91精品国产色综合久久不卡| 性生交大片免费看av| 日本免费人成在线播放视频| 人妻久久一区| 国产精品自产拍在线观看花钱看| 久久精品人妻少妇| 丁香五月亚洲综合在线国内自拍| 精品高清一区二区三区| 欧美日韩一区二区三区v| 我去也我来也www色| 日本在线有码电影网站| 青春草免费观看视频大全下载 | 日韩欧美资源在线观看| 97久久a 99精品综合噜噜五月天| 国产麻豆aⅴ精品一区二区| 超逼视频免费国产| 国产精品香港三级av| 末成年AV女网站| 欧美国产成人一区二区三区| 国产成人亚洲综合图区| 一级黄色a大片| 午夜理论2019理论无码| 亚洲欧美校园丝袜| 国内精品视频自在欧美一区| 亚洲伦理av在线| 亚洲国产另类久久久精品性下载| 大学生久久香蕉国产线看观看| 亚洲精品久久无乱码| 又硬又粗又爽黄色视频| 97久久精品国产精| 2021国产麻豆剧传媒免费| 国产精品一区二区三区绯色av| 久久av蜜桃一区二区三区| 日韩亚洲成人一区二区| 亚洲一区二区三区专区精品| 性啪啪chinese东北女人| 久久精品国产清高在天天线| 一本色道久久综合无码| 18禁在线欧美| 波多野结衣演的人妻| 免费观看a一片| 亚洲国产成人久久久| 国产在线观看无码的免费网站| 丰满熟妇老熟女av| 日韩一区二区三区免费片| 扒开女人下部添高潮的视频| 可以免费看毛片的网址| 国产国内久久精彩国语对白视频| 亚洲av人人澡人人爽人人夜夜| 性生交大片免费看av| 美女极品粉嫩美鮑20P图| 亚洲免费中文电影一区二区三区| 日韩不卡中文| 三级毛片的视频播放的| 国产亚洲欧美经典电影| 成人av原网站| 又粗又硬又爽免费视频| 国产在视频线精品视频午夜视频| 国产一区二区高清视频女| 三级全黄色毛片a级全黄色毛片| 欧美亚洲精品一区播放影院| 97久久人人人妻人人玩| 久久精品人妻av一区二区三区| 日韩电影三级一区二区三区在线观看| 熟女久久久久久久久久| 亚洲欧洲av高清| 国产亚洲精品aaa在线观看| 日韩精品久久久久免费影院| 亚洲成AV人不卡无码影片| 久久伊人毛片av| 久久精品国产亚洲精品av| 伊人青青大草原| 日韩大码丰满熟妇| 天天综合网久久综合免费人成| 丁香色婷婷综合激情| 黄色a级毛片| 丰满熟女乱又伦| 日韩成人av一区二区三区| 久久国产精品香蕉| 性生大片免费观看性| 久久红精品一区二区三区| 96久久精品人人妻人人爽| 超短裙夹道具羞耻h| 亚洲高清成人一区二区三区| 小草影院一区二区| 啪啪人妻一区视频| av尤物网站在线观看| 最好看2019中文字幕高清视频| 精品毛片aaa级| 国产成人综合久久免费| 成年日本片黄网站| 亚洲欧美另类日韩中文字幕| 超级大乳人妻无码| 成人国产av精品蜜臀下载| 亚洲av和国产综合av| 久久精品亚洲乱码| 日本无遮羞肉体动漫在线观看| 亚洲av日韩av国产精品| 国产传媒天美一区二区三区| 久久精品国产精品亚洲艾草网| 人人爽夜夜精品| 男欢女爱a级毛片| 男女18禁无遮挡网站| 国产色综合久久无码有码| 成人黄色免费在线视频| 婷婷色麻豆天堂久久| 少妇人妻偷人激情| 少妇特殊按摩高潮不止| 啪啪动图边摸边吃奶做爽动态| 色婷婷激情av精品影院| 久久一级片电影| 亚洲一区二区三区在线播放_ | 在线观看一区二区精品| 美女黄频视频网站大全| 久久久亚洲精品成人一区二区| - BD韩语手机在线看| 美女视频黄频大全aaa| 中文字幕密臀av首页熟女人妻| 亚洲欧美久久精品| 小太正Gay初精自慰 | 中文字幕好看男人天堂网 | 超帅男生同志TWINKS视频| 青青青国产在线视频在线观看| 亚洲精品欧美国产入口| 国产精品a一区二区三| 亚洲欧美日韩精品网| 亚洲免费视频自拍一区| 97se亚洲国产综合自在线观| 亚洲av高清一区二区重口| 日本一本二区三区精品| 97久久国产精品一区| 人妻少妇精品久久人妻| 国产人人做人人爽| 国产日韩av高清在线不卡| 三级伦理电视剧| 男女做爰猛烈吃奶摸大胸视频| 亚洲欧美日韩在线播放一区二区| 少妇高潮喷水下面的毛| 亚洲自拍偷做受| 精品久久久久久久久久久国产字幕日 | 大香蕉视频国产在线| 久久久精品人妻一区二区三区四| 亚洲美女天堂婷婷| 97人妻人人澡人人爽| 婷婷色综合大香蕉| 欧美色a一区二区| 人妻少妇精品天堂毛片在线| a片太大太长太深好爽在线观看| 亚洲成a人线上播放| 国产伦精品一区二区三区| 成人免费视频www| 一卡二卡三卡免费看| 正在播放国产多P交换视频| 国产女人18毛片水真多精选| xxx日本一二三区不卡| 亚洲欧美最大色精品网站| 强d乱码中文字幕熟女亚洲| 国产成人精品电影在线观看91| 好男人视频免费观看高清www| 日韩大片免费观看网址| 精品国产一区二区三区不卡| 亚洲欧美国产一区在线观看| 久久综合亚洲综合91精品国| 亚洲自拍九九视频| 欧美激情视频网站| 波霸av免费| 日韩午夜精品福利视频| 国产精品原创巨作AV无遮挡| 国产极品女主播国产区| 人人爱人人做人人干| 18禁无遮挡黄网| 日本按摩高潮A级中文片| 人人妻人人澡人人爽的| 边吃奶亚洲一区二区| 欧美成人精品第一区二区三| 一本大道久久a久久精品| 精品国产成熟老妇女| 日本乱理伦片在线观看真人| 成·人免费午夜无码视频在线观看| 五十熟女人妻视频一区二区 | 亚洲精品av在线免费观看| 国产欧美日韩综合网| 亚洲日韩精品无码专区网站| 国产精品国产三级国产专区50| 国产精品宅男电影| 国内熟骚老妇| 久久亚洲综合在线| 亚洲人成网站色www网址| 日日噜噜噜夜夜爽爽狠狠同性男| 欧美人与拘性视交免费| 国产一区二区在线观看网址| 麻豆国产麻豆| 亚洲中文子幕乱码电影| 日本视频播放一区| 日本妇人成熟免费视频| 精品视频国内精品视频| 久久精品亚洲老司机视频| 两个男人吮她的花蒂和奶| 伊人久久大香线蕉一区二区| 国产午夜欧美日韩| 一区二区亚洲精品国产av| 五月天丁香婷婷色| 熟女人妻av一区二区| 性欧美精品18videosex| 午夜福利av线上网站| 91丝袜美腿诱惑| 国产一区二区三区ww视频| 美女上床视频免费观看| 国产精品一区二区三区免费观看| 欧美zo000极品另类| 欧美日韩国产精品精品| 69久久夜色精品国产| 亚洲av日韩av综合| 欧美激情国产视频一区| 特黄特大黄色片| 丰满熟女午夜视频| 午夜久久鲁丝片| 在线观看网站日韩免费网站| 欧美性狂猛xxxxxbbbbb| 午夜福利片1000无码免费| 国产在线视频激情| 国模欢欢炮交啪啪150| 国产亚洲欧美日韩在线三区| 女厕真实偷拍撒尿视频| 久久精品国产亚洲AV网站| 欧美骚比在线视频| 亚洲91|日韩| 亚洲欧美日韩在线系列| 欧美日韩大片网站| 国产精品二区av| 欧美日本中文国产一区发布| 97婷婷大香蕉| 在线播放成人av| 午夜诱惑在线观看亚洲av| 老鸭窝免费宅男| 欧洲在线一区二区三区| 亚洲毛片不卡AV在线播放一区| 真实国产乱子伦沙发| 国产综合色产在线精品| 国产精品综合亚洲区| 国产女主播喷水视频免费看| 国产三级黄色录像| 一区二区日韩电影院| 日本国产高清一区二区三区| 国产精品人妻一区一区三区| 国产精品亚洲欧美日韩| 大香蕉免费成人蜜桃| 亚洲最大无码AV网站观看| 少妇多b内射| 亚洲国产日韩A在线乱码| 医院人妻隔着帘子被中出| 国产精品亚洲А∨天堂网不卡| 8×8X永久免费视频在线观看| 午夜电影院韩国三级| 毛片9673 | 美女高潮喷水被强摸下面| 99久久伊人精品影院| 激情老司机福利69影院| 亚洲欧洲国产av码| 午夜精品久久久久久久久| 男生把女生操出白浆的视频| 激情五月亚洲综合图区| 小说一区二区图片视频| 色综合色国产| 午夜a级毛片免费观看| 国产一级特黄高清在线大片| 国产av高清精品久久| 小SAO货水好多真紧H视频| 五十熟女人妻视频一区二区| 狠狠久久亚洲欧美专区| 免费无遮挡裸体视频| 免费99久久| 可以免费看a级毛片| 亚洲国产成人精品软件| 国产极品女主播国产区| 国产又黄又粗又爽女视频| 亚洲国产韩国欧美在线| 99精品国产兔费观看久久| 精品久久久久久久熟女| 少妇寂寞难耐被黑人中出| 欧美日韩国产免费一区二区三区 | 美女被日高潮国产| 被公侵犯玩弄漂亮人妻| 97热精品久久久久久| 给我免费播放高清视频观看| 久久一级黄片免费| 亚洲欧洲国产综合a| 久久久成年人免费电影| 精品国产福利网站| 久久不见久久见中文字幕免费| 看一个黄色一级片| 麻豆激情四射av| 亚洲精品美女xxoo| 先锋77xfplay色资源网站| 全黄男人和女人视频| 97在线中文字幕不卡码| 西西人体大胆啪啪私拍| 无遮挡激烈网站| 精品久久国产亚洲av| 无码超乳爆乳中文字幕| 福利午夜精品电影| 91久久婷婷国产综合精品免费| Al—娜塔莉·波特曼| 久久99精品国产麻豆| 日韩精品无码一二三四区A片| 午夜福利av不卡| 亚洲黄片av在线播放| 97视频在线视频免费观看| 亚洲国产精品成人综合色| 国产精品久久久久久91蜜桃| 丰满日韩放荡少妇无码视频| 国产欧美日韩中出| 国产久一视频在线观看| 白饿罗斯毛片| 精品人妻有码| 国产40岁熟女精品观看 | 在线BT天堂WWW在线| 永久免费观看美女啪啪视频| 日韩国产中文韩国欧美亚洲另类在线观看| av片不卡免费播| 老熟女偷人视频在线| 毛片视频免费播放器免费播放| 国产毛片毛片毛片|久久女人视频| | 国产亚洲精品一区999| 国产精品久久激情毛片| 变态挤奶水AV大片| 亚洲老熟女在线观看| 亚洲第一av网站久久| 久久久久亚洲精品牌| av成人不卡在线| 午夜福利av不卡| 亚洲日本不卡| 亚洲永久中文字幕| 久久精品国产亚洲av香蕉上下| 黄片免费在线播| 99re视频在线观看免费| 天堂√中文在线官网在线| 国产一级内射老妇| 亚洲不卡高清免费在线视频| 成人性生交大片免费看一4| 久青草国产手机在线观看| 成年版毛片免费区| 黑人30厘米全进去视频| 成年人可以看的黄片| 俄罗斯多毛肥女BBW| 女人精品久久久久毛片| 婷婷开心五月人人| 国产国语露脸对白视频| 在线观看国产999av| 国产精品久久久久久久久久电影网 | 国产麻豆国产精品| 久久人人妻人人人人爽软件| 国产精品国产三级国av中文| 精品v亚洲v欧美v高清v| av男人的天堂国产在线观看| 一区二区小说图片视频| 亚洲国产精品片| 啪啪动图边摸边吃奶做爽动态| 日产精品卡1卡2| 97涩国一产精品久久久久久久| 国产麻豆精品一区二区粉嫩av| 欧美老熟妇乱人伦人妻| 精品久久久久久久av| av不卡网站在线观看| 国产精品乱码久久久久久久久| 久久久久精品av毛片| 一级a一级a爰片蜜臀av| 亚洲美女网免费观看| 99这里精品| 日韩欧美大片免费观看| 亚洲欧美色国产精品| 18禁止美女裸体看免费| 一级片免费观看大全| 四虎永久在线精品免费视频观看| 一边摸一边爽一边叫床全过程软件| 肉体裸交137日本大胆摄影| 午夜大片久久久久成人| 国产精品区久久久| 最近2019年免费中文字幕大全| 可以看内射的视频| 巨乳视频在线看| av天堂手机版亚洲| 毛都没有就被开了苞在线电影| 狠狠久久这里只有精品| 99久久一区二区三区免费| 第一午夜少妇福利影院| 国产成人咱精品视频免费网站| 美女福利在线观看| 亚洲国产人久久久成人精品网站 | 亚洲JIZZJIZZ妇女| 国精品午夜福利视频不卡无毒| 欧美人与禽ZOZ0性伦交| 中文字幕视频精品一区二区三区| 国精品久久久久久国模美| 18禁羞羞视频无遮挡免费| 美女上床视频免费观看| 亚洲中文字幕乱码在线视频| 国产日韩在线一区二区在线| 亚洲b片免费观看| 黑人激情视频在线| 有黄有色无遮挡网站| 国产呦系列呦交| 午夜理论片最新午夜理论| 搡女人真爽免费视频大全软件| 亚洲人成网站精品在线观看| av伊人久久免费久久av| 少妇的丰满3中文字幕| 日韩黄色录像欧美黄色录像| 久久精品一区亚洲| 成年人的毛片视频| 少妇人妻精品久久888| 精品亚洲AV无码一区二区三区| 美女黄频视频大全免费的视频| 国产又大又长又粗又爽视频| 狠狠久久精品婷婷| 国产亚洲综合成人a精品| 天天操一操,| 国产欧美精品在线一区二区三区| 欧美精品电影一区二区三区| 亚洲a在线观看免费视频| 91中文字幕色在线| 最近更新2019中文字幕免费 | 黄色裸体视频无遮挡| 亚洲一区在线观看美女| 国产精品视频内射| 亚洲精品国产a久久久| 91视频亚洲欧美| 成年人毛片视频| 亚洲JIZZJIZZ妇女| 久久欧美日韩| 国产高清精品免费精品| 免费看小12萝裸体视频国产| 国产精品一二三区在线观看| 国产又黄又粗又爽女视频 | 国产精品久久久久久av免 | 久久伊人精品色婷婷国产| 亚洲一区二区三区不卡在线| 国模一区二区三区四区视频| 在线观看人成激情视频| 国产日韩av高清在线不卡| 我想看日本黄色视频| 国模吧GOGO裸体私拍| 午夜福利国产在线观看2| 久久久久久亚洲精品杨幂圣光| 沈阳60老熟女高潮| 精品人妻自拍视频中国大陆| 成人亚洲1区二区| 免费观看超爽A片| 久久国产精品福利一区| 欧美最新免费一区二区三区| 精品国产一区二区三区av网站| 97久久综合区小说区图片区| 少妇逼呻吟喷水视频网站| 国模一区二区三区四区| 国产在线观看男天堂| 国产婷婷香蕉久久久久久| 国产精品色婷婷久久99精品| 一区二区欧美成人福利| 无码无遮拦午夜福利院| 狠狠亚洲综合| 午夜视频精品福利| 最近最好看的中文字幕2019| 女人的超长巨茎人妖在线视频| 两个人在线观看的www视频| 免费观看男女性高视频| 国产精品久久草| 中国少妇BBWBBWHD| 中文字幕三级视频网站| 亚洲第一电影网av| 对白离婚国产乱子伦视频大全| 欧美性大战久久久久久精品| 色综合夜夜躁很很躁日日躁2| 我被黑人插的太舒服了啊啊啊啊视频 | 亚洲人成网站高清观看| 亚洲影院一区二区三| 白丝班长深夜被啪到娇喘不停| 日韩中文字幕永久视频| 免费观看精品视频网站| 99免费的精品视频| A级黑粗大硬长爽猛视频| 伊人久久大香线蕉av影院| 久久99热6这里只有精品| 被黑人猛躁10子高潮视频| 欧美性BBBBBXXXXX| 中文字幕在线丝袜诱惑| 麻豆女人毛片| 女人精品久久久久毛片| 中国黄色一级毛片孕妇| 玉蒲团之玉女心经| а√天堂资源地址在线官网下载| 久久变态另类亚洲精品| 熟妇午夜精品久久久久| 特别黄的免费大片| 亚洲嫩草影院| AV片在线观看| 99re热在线视频播放| 久久国产精品乱子乱精品| 国产在人线视频| 人人妻人人爽人人插| 亚洲av日韩aⅴ中文在线不卡| 亚洲精品国产字幕久久久| 精品久久精品色综合| 三级电影一区二区三区| 欧洲美女与动交Z0Z0Z| 高清一级黄色片| 精品一区久久三区二区| 97精品国产一区二区三区四| 无遮挡边吃奶边做刺激视频呻| 18禁网址_亚洲欧美精品综合久久99 | 成人黄色视频中文字幕| 国产欧美日韩91在线| 最近2019免费中文字幕6| 国产成人av片在线| 免费av线上播放| 又粗又硬又爽免费毛片视频| 暖暖视频中国在线观看免费韩国| 粗长巨龙挺进人妻后臀| 国产精品视频免费在线播放| 国产亚洲精品aaa在线观看| 亚洲av综合成人久久久| 制服亚洲欧美中文高清| 欧美激情久久综合| 精品久久青草| 攵女乱H边做边打电话| 黄色精品在线观看| 亚洲av一影院| 日本亚洲视频一区| 夸克免费电影大全播放器| 97热精品久久久久久| 毛片免费网站有哪些| 国产一区二区三区在线观看av| 扒开女人下部添高潮的视频| 亚洲av电影高清在线观看| 国产黄在线观看免费播放| 欧美另类69xxxxxxx| 免费人妻精品一区二区三区0| 日本少妇高潮日出水了| 亚洲一区二区三区在线观看电影| 男人把女人桶到爽免费| 熟女人妻中文字幕av一区| 精品久久久久久久久视色限时免费| 国产午夜福利大片免费看| 婷婷激情五月天麻豆| 99久久国产精品黄片| 免费黄色在线视频网站| 久久麻豆精亚洲av品国产麻豆 | 亚洲av动漫一二区网站| 精品国产乱码一区二区三区蝌蚪| 精品少妇熟女在线| 久久久国产99久久国产久麻豆| 狼人国产精品成人av| 免费成年一级毛片| 人伦乱高清视频在线观看| 一本色道av久久精品| 又黄又湿啪啪响18禁| 黄色一级片网站久久| 亚洲成人久久一二三区| 中文字幕三级视频网站| 成年女人免费影院| 国产日韩精品成人| 国产老妇女一区二区| 亚洲av乱色| 高清中文字幕国产| 亚洲色图av天堂| 五码一区二区三区| 午夜福利黄片免费看| 两个人的电影免费视频| 欧美videossex精品| 中文字幕在线永久免费播放| 黄色毛片免费孕妇| 黄色理论视频在线观看| 最近中文视频字幕大全| 国产成人三级黄色片| 日日爽夜夜拍| 东方在线一级毛片| 中文有码无字幕| 天天摸夜夜添狠狠添高潮出水| a中文天堂在线| 国内精品在线免费视频| 国产一级一区二区在线观看| 婷婷国产成人一区二区| 免费看a级毛片全部在线播放视频| 国产欧美亚洲精品第1页| 成熟丰满熟妇高潮ⅹ久久精品| 国产精品一区乱码| 国产福利一区二| 日日做夜夜爱夜夜爽av毛片| 午夜诱惑老司机视频| 亚洲熟妇中文字幕五十中出| 日本wwww免费看| 亚洲欧美精品专区久久| 神马影院九老司机| 亚洲国产欧美av| 日本国产欧美不卡| 亚洲最大91av色| 99久久99这里只有精品免费视频| 亚洲国产成人久久精品一区| 亚洲中文精品乱码| 亚洲aⅴ每日更新在线观看| 亚洲最大精品日韩一区| 亚洲高清精品乱码| 欧美老熟妇乱人伦人妻| 亚洲欧美精品中文字幕在线观看| 95同城少妇高潮喷水视频| 亚洲+欧洲+日产+韩国精品| 男女92视频在线观看| 人妻系列中文字幕在线播放| 国产日韩欧美v| 香蕉在线视频精品| 国产丰满老熟女重口对白| AV香港经典三级级在线观看| 猫咪av最新永久网址| 黑人30厘米全进去视频| 亚洲天堂日韩欧美在线| 黑森林精选AV导航| 少妇人妻视频网站| 亚洲国产精品亚洲一区二区三区| 99精品三级久久久久| 成人a级毛片免费看| 久久夜色精品亚洲噜噜国| 男女下面进入的视频免费午夜| 中国美白少妇内射xxxbb| 久久国产精品ww| 久久久国产老熟女| 超碰97国产精品| 日韩欧美亚洲一区66| 午夜无遮挡在线免费观看| 663个4点半| 精品综合久久国产 | 美女视频黄是免费视频| 精品国产自线午夜福利| 欧美色倩网站大全免费| 高潮美女一区视频| 可以免费看毛片的网站| 99久久精品在| 亚洲av综合一区二区三区| 亚洲av高潮喷水久久天堂| 色丁香开心五月| 日日噜噜噜夜夜爽爽狠狠同性男 | 久久久久久国产一级资源| 午夜福利免费试看| 中文字幕欧美精品一区二区| 人妻少妇福利视频| 日韩综合一二三区| 中文字幕在线观看巨乳| 欧美日韩视频在线观看一区二区| 女人18毛片a级毛片一高清观看视频| 久久久人妻视频网| 老司机午夜精品影院| 亚洲精品国产字幕久久久| 日韩精品有码中文字幕在线| 亚洲精品一区二区三区播放| 在线成H人视频免费| 不卡av在线播放观看| 熟妇草逼视频| 国产精品成久久久久久| 男女下面进入的视频免费午夜| 亚洲av午夜免费观看| 亚洲成a人片在线观看视频| 日韩不卡avwww| 香港绝版无码老A片| 俄罗斯victory day青年| 国产一区二区二三区| 超级教师免费观看完整版| 国产乱人伦精品一区二区视频| 美女露出100%奶头的视频| 欧美亚洲丝袜另类| 免费一线看视频| 在办公室狂摸老师下面视频| 精品人妻av在线免费观看| 久久人人爽人人爽爽久久| 国产男女猛烈交配视频免费观看网站大全 | 国产亚洲欧美中文字幕在线| 97久久久国产精品消防器材优势| 午夜天堂影视香蕉久久| 国语刺激对白在线视频播放| 国产亚洲日韩一区二区三区| 一本大道东京热无码AV| 久久一级片免费看| 日本一级a爰片| 亚洲精品少妇熟女| 被持续侵犯的中文字幕| 免费人妻精品区一区二区三| 国产av精品一区二区| 成年版毛片免费区| 男女边摸边吃奶边做视频大全| 中国老妇欧美熟女| 亚洲精品在线中文字幕| 国产精品视频大全免费观看| 国产一级片男人天堂| av大香蕉在线| 侵犯洗澡女教师在线观看| 女人操男人在线观看| 久久99国产一区二区| 美女网站免费观看视频| www.一级毛片在线播放放| 先锋影音AV最新AV资源网| 黄床大片30分钟国产精品| 国产美女免费视频| 亚洲最大的人成网站| a级毛片毛片免费观看久潮| 内射国产在线视频| 99精品国产免费久久久久久| 国产精品免费久久久久大片| 亚洲欧美国产成人久久| 人妻少妇精品专区性色AV| 99rr在线视频| 午夜不卡av电影免费看| 亚洲成a人线上播放| 免费看女人的隐私超爽| 亚洲国产色综合| 久久这里只有精品中国| 99热在线精品这里只有精品 | 麻豆乱淫一区二区三区| 久久久精品国产亚洲成人满| 色婷婷偷男人的天堂| 美国成年女毛视频| 亚洲第一av色| 桃花在线观看免费观看手机| 偷拍粉嫩25位美女厕所| 亚洲色图男人天堂中文字幕| 免费在线观看国产午夜激情| 国产午夜羞羞小视频在线观看免费| 日本三级高清| 被侵犯的人妻电影视频| 在线观看成年人片| japanese国产真实乱| 西西人体亚洲av高清大胆| 免费国产无遮挡黄的网站| 日本少妇高潮日出水了| 全部毛片免费在线播放| 草莓视频毛片免费看| 久久国产亚洲欧洲| 欧美乱妇无乱码高清| 国产精品一区av久久久免费观看| 在线观看免费国产黄片啊啊啊受不了了 | 白丝班长深夜被啪到娇喘不停| 97欧美精品一区二区三区| 亚洲aⅴ每日更新在线观看| 亚洲欧美一区二区三区| 国产精品一区二区夜色不卡| 国产亚洲精品久久小说| 国产精品VA在线播放| 日韩电影亚洲av| 男人舔女人下部高潮全视屏| 成人国产av精品蜜臀下载| 成人高清毛片| 国产精品一区二区免费欧美| 黄色色禁免费看| 免费操人妻一区二区| 久久久久久久一级黄| 国产免费观看a大片的网站| CHINESE粗口篮球体育生| 99久久国产综合精品女小说| 91精品国产国语对白视| 国产精品原创巨作AV女教师| av天堂中文字幕网| 日韩欧美电影高清爱情片电影| 免费人成网站在线观看不| 亚洲欧美一区二区三区黑人| 在线私拍国产福利精品| 国产性色强伦免费看视频| 成年女人视频专区| 美女扒了内裤让男人桶| 国产精品一区二区欧美日韩| 久久精品国产亚洲av香蕉上下| 国产美女视频黄a视频免费| 一级做a爰片久久免费观看 | 国产无套乱子伦精彩是白视频| 亚洲国产精品综合欧美| av电影网站在线| 国产呦系列呦交| 美女高潮喷水观看网站| 亚洲在线看片| 首页国产激情对白| 日韩人妻一区三区| 色欲香天天天综合网站无码| 亚洲av网站专区| 啪啪啪高潮喷水视频| 精品熟女一区| 国精品午夜福利视频不卡无毒| A毛片免费全部播放完整| 国产福利精品一区| 天堂网最新版资源在线www| 免费观看男女午夜视频| 国产卡1卡2卡4卡精品欧美| 精品中文字幕资源网站大全| 国产色综合视频| 岛国永久av网站| 国产精品欧美日韩电影| 亚洲精品久久久久久图片| 欧美性XXXX极品少妞| 18禁国产精品久久久久久久久小说| 久久久精品欧美一区| 午夜激情不卡视频| 久久久久久久免费免费精品 | 国产欧美性成人精品午夜| 97在线中文字幕不卡码| 国产精品VR无码专区| 黄床大全三级网| 久久久久久久免费黄色视频| 美日韩视频一二三区| 亚洲aⅴ精品一区二区三区小| 国产精品欧美一区二区三区| 又黄又爽又粗又硬视频| 亚洲国产精品女人26p| 国产老妇女一区| 美女爽到高潮喷出尿来的网站| 午夜av免费爱爱| 11孩岁女精品毛片免费| 神马午夜福利视频在线观看| 日本人人妻人人澡人人爽| 在线激情成人小视频| 人妻午夜中文字幕| 4个闺蜜疯狂互换 5P同床好爽| 亚洲视频日本色片| 亚洲AV第一成肉网| 伊人久久大香线蕉av成人| 韩国伦理片在线观看最新| 国产av亚州av| 九草视频在线免费观看| 日日躁夜夜躁夜夜揉| 日本淫秽高清视频| 国产成人亚洲综合色| 国产情侣色在线| 国产喷水高潮在线观看| 国产三级电影在线免费播放| 一区二区日韩免费视频| 秋霞一级成人毛片免费看| 国产麻豆剧果冻传媒观看| 亚洲最大精品日韩一区| 成年女人观看永久免费视频| 精品v亚洲v欧美v高清v| 天堂在线中文在线6| 日韩人妻精品av在线| 日本六区视频| 中文字幕在线丝袜| 日本人69xXⅹ69护士| 国产欧美日韩高清不卡| 国产精品成人黄片在线播放| 日韩a级毛片免费观看在线 | 国产日韩欧美第一区第二区| 中文字幕在线丝袜| 金梅瓶1一5集手机在线观看| 久久久久国产刺激毛片| 看黄蝶一级录像一级毛片| 免费观看欧美色视频| 久久永久免费专区人妻精品| 国产熟女精品| 国产成人久久久精品二区三区| 女国产精品视频一区| 叉开腿做爽爽视频| 国产成人三级一区二区在线| 日韩高清网页| 少妇私密推油呻吟在线播放| 成年女人视频免费| 久久av免费大片| 搡女人真爽免费视频大全软件| 久久午夜夜伦鲁鲁片免费无码| 国产成人剧情av麻豆映画1| 国产黄色av片免费播放 | 搡老女人911熟妇老熟女 | 在线BT天堂WWW在线| 啦啦啦资源在线完整视频| 日韩久久亚洲一区| 性xxxx欧美老妇胖老太269| 91影院午夜福利| 硕大黝黑粗大的噗嗤噗| 国模1区2区| 国片av国产精品| 色呦哟—国产精品系列| 亚洲精品国产成人a| 久久品国产亚洲av香蕉| 偷拍视频一区二区三区四区| 99久久精品免费看国产一区| 关于爱的电影完整版| 一级a爰片性视频特黄| 国产三级电影在线免费播放| 国产精品老熟妇女人| 黑人激情视频在线| 又粗又爽又猛毛片免费看| 揉我奶头啊嗯免费视频| 亚洲电影乱码一区二区三区| 男人天堂网久久| 免费人成在线观看网站品爱网 | 日本一区黄色视频网站| 99久久精品久久免费观看不卡 | 国产不卡在线一区二区三区| 久久精品aⅴ一区二区三区四区 | 色多多成人黄在线观看| 精品人妻av区天天看片波多野结衣 | JⅠZZJLZZ亚洲大全| 一本大道久久久久久久精品| 久久最近中文字幕| CAOPROM国产在线视频| 久久熟女人妻| 黄色免费av| 岛国av高清不卡免费| 日日爽夜夜爽网站| GV无码免费无禁网站| 亚洲中文字幕在线高清m| 97久久久国产精品消防器材优势| 亚洲中文无码AV永久主页不卡| 亚洲av高清一区二区三区尤物| 漂亮人妻被同事疯狂玩弄| v片视频在线观看了| 99精品少妇一区二区三区| 日韩亚洲AV无码一区二区三区| 欧美亚洲国产日韩专区 91| 两个嫩嫩的小奶头| 国产AⅤ无码专区亚洲AV| 久久久亚洲精品区| 免费看女人一级毛片| 国产娇小粉嫩学生免费网站| 中文字幕久精品视频免费| 99国产精品v| 高清在线观看视频不卡播放| 久久亚洲av精品毛片二区| 天天躁日日躁夜夜躁免费视频| 国产日韩欧美一区二区| 国产av日韩精品xyz| 美女黄网站免费福利视频| 午夜高清福利视频| 久久亚洲av精品毛片二区| 97久久超碰国产精品新版| 日本淫妇xxww| 69毛片免费视频观看| 一本大道久久a久久综合婷婷| 饥渴少妇高潮舒服死了| 欧美不卡视频免费观看| 日本免费新一区视频| 亚洲一区二区三区| 999国产成人免费视频| 新狼窝色av性久久久久久| av午夜网站| 国产一精品一av一免费爽爽| 日日碰狠狠躁久久躁| 日韩欧美中文字幕视频在线看| 14—18CARD学生| 国产av麻豆天堂亚洲av刚刚 | 欧美性乱xxx| 18禁无遮挡无打码| 日韩欧美亚洲综合一区| 亚洲黄色av视频| 一级做a爰片久久精品毛片| 人妻av无码专区久久| 日本欧美日韩一区| 亚洲中文字幕日韩| 九月婷婷人人澡人人添| 青草草免费视频网站| 亚洲欧美在线va| 一区二区日韩电影院| 日本亚洲va午夜影视| EEUSS影院WWW在线观看| 毛多内射在线视频| 日韩国产亚洲| 欧美成人激情久久| 欧美日韩中文字幕一区二区| 国产亚洲欧美日韩综合一区在线观看 | 成人区人妻精品一区二区18| 国产精品一品二区三四区| 丰满人妻中伦妇伦精品a| 人人妻人人澡人人爽欧美精品| 综合欧美亚洲日本| 国产亚洲精aa在线| 黑人xx性精品| 日本aaaa片爽快免费19| 亚洲va在线播放观看| 小sao货大ji巴cao死你h视频| 精品国产男人天堂| 国产伦人伦偷精品视频| 日韩精品在线久av观看| 美女高潮爽到喷出尿来网址| 亚洲国产欧美日韩二区三区| a级毛片免费基地| 少妇超爽一区二区三区| 麻豆国产麻豆| 深夜福利免费卫生纸请准备| 成人国产av精品蜜臀论坛| 人妻销魂中文字幕av| 日韩黄色大片网站| 波多野精品一区二区三区色情| 成熟老太毛茸茸BBWBBW| 被黑人侵犯中文字幕一区| 国产福利精品99| 久久精品111| 国产乱码精品一区二区三下载 | 男男chinese男男资源| 国产一级内射视频www| av天堂高潮| 日韩亚洲欧美综合| 亚洲精品影院一区二区| 国产精品视频视频一区| 中国人妻4P野战VIDEO| 精品人人妻人人澡人人爽牛牛| 日韩亚洲高清av| 一夜夜www| 国产精品成人久久网| 亚洲少妇38p| 国产无遮挡无码视频在线观看| 亚洲av 日韩国产| 日本与欧美在线观看| 日日摸夜夜添夜夜添日韩| 国产明星裸体XXXX视频| AV片亚洲国产男人的天堂| 男人J进女人J的视频| 人妻熟女かぁ～たん| 国产欧美亚洲福利| 女人18毛片| 久久久久夜夜夜猛噜噜| av在线日韩国产| 日本最新色视频在线观看| AV片在线观看| 亚洲精品天堂av在线| 91色老头与人妻中文字幕视频| 亚洲春色少妇熟女小说| 少妇人妻精品久久888| 特别黄的免费大片| 免费av大蜜桃| 成人午夜特黄AAAAA片男男| 体育生小鲜肉GAY自慰| 久久人妻人精品| 久久中文字幕专区| 国产精品一区激情电影| 亚洲国产综合欧美| 亚洲精品下载| 99午夜福利视频?| 两个人的视频免费视频下载| CHINESE粗口篮球体育生| 国产熟女一区二区三区黄| 学生双腿白浆高潮视频| 性按摩XXXX| 日本激情黄色视频网站| 精品人妻波多野结衣一区 | 国产丁香六月| 熟女人妻系列av波多野结衣| 看成年女人午夜毛片| A毛片免费全部播放无码| va欧美va亚洲综合在线观看| 国产AV国片精品有毛| 香蕉国产在线观看| 亚洲av免费视一区| 日韩欧美aⅴ一区二区三区| 午夜福利av线上网站| 亚洲91青青中文字幕| 我们高清日本视频免费观看| 中文字幕第一页久久| 久久国产亚洲精品嫩草| 国产精品96久久久久孕妇| 秋霞在线观看的av| av在线影片| 亚洲国产精品8x| va激情在线看免费 | 龚玥菲版新梅瓶在线观看| 曰本A级毛片无卡免费视频VA| 91精品国产色综合久久不卡| 人妻久久久久久精品免费免费| 久久人妻人人爽人人爱91| 日本mv网站免费看| 少妇把腿扒开让我爽爽在线观看| 东京热av男人的天堂av| 一级av一片久久免费观看| 亚洲经典成人影院| 久久这里只有精品666| 亚洲视频成人免费观看| 日韩av影片网址| 国产熟女极品| 男人添女人下部高潮免费看| gif动态啪啪啪| 欧美成人精品第一区二区三| 青草草97久热精品视频| 国产精品久久久久久久久久蜜臀| 日日碰狠狠躁久久躁| 久久亚洲综合激情| 一级a一级a爰片免费2022| 久久综合网亚洲国产| 色婷婷久久久亚洲欧美| 特级毛卡片普通话不收费| 精品久久久久久,| 99热6这里只有精品| 欧美精品人与动牲交sv欧美| 中文乱码字字幕精品一区二区三区| 一区二区三区四区激情视频 | 91香蕉在线精品视频| 国产精品成人国产乱| 午夜精品久久久久久久久| 欧美性受xxxxx| 欧美国产日本在线不卡| 亚洲五月色婷婷综合开心网| 一区二区毛片免费看| 爱像一片宽阔的湖泊| 精品人妻小视频| 亚洲欧美国产一区二区在线观看| 久久99国产乱码一区二区三区| 少妇被粗大的猛进出| 娇妻被猛男老外玩三P| 亚洲一区av在线蜜臀| 亚洲av极速不卡在线观看| 白丝粉嫩小仙女自慰网站| 日韩岛国大片av久久久久久久| 免费欧美一区二区激情视频| 欧美乱妇乱码| 国产真实乱的伦视频| 日本高清视频免费观看网站| 熟女人妻av一区二区| 国产无遮挡裸露视频免费| 国产午夜精品电影院| √天堂资源网最新版在线| 1卡2卡三卡3卡4卡精品| 女黑人RAPPER超级胖的汽车 | 亚洲av专场在线观看| 精品久久久了| 国产精品三级手机在线| 国产美女精品av在线观看| 色综合另类小说图片区| 大量国产私密保健视频| 免费国产伦精品一区二区三区| 99热之这里只有精品网| 97人妻人人爽人人精品| 99精品老司机免费视频| 亚洲乱码中文字幕97精品| 精品国产日韩亚洲一区| 99热精品就在这里| 欧美精品乱码久| 亚洲综合色区另类小说| 天天影视网色香欲综合网| 无码小电影在线观看网站免费| 中文字幕在线永久免费播放| 一级做a爰片久久精品毛片| 亚洲欧美国产精品| 日本一级毛色大片| 久操精品在线视频| 男女一边摸一边做爽爽视频| 唐山熟女高潮喷水| 日本国产二区不卡| 一二三区人妻| 精品人妻少妇嫩草av免费专区| 国产精品久久久天天影视香蕉| 深爱激情五月婷婷| 亚洲男人天堂免费在线| 好色av在线| 韩国大尺度电影| 无码爆乳护士让我爽| 日韩av电影在线看一区二区| 久久久亚洲精品免费| 麻豆果冻国产91在线极品| 无遮挡啪啪摇乳动态图| 欧美日韩中文字幕| 久久人人爽人人爽人人片va| 久久国产精品熟女一区二区三区| 青草青草久久| 内地中年熟妇露脸视频| 国产熟女高清| 欧美日韩国产精品久久综合人妻| 一区二区亚洲精品国产av| www日本免费com| 成熟女人牲交视频| 91精品老鸭窝在线观看| 日本熟妇乱子伦XXXX| 两个人BD高清在线观看2018年 | 亚洲和欧美一区二区三区| 一区二区三区国产精品乱码| 中文字幕小明永久| 99午夜福利| 亚洲欧洲日产国码综合在线| 国产亚洲精品乱码久久久久久| 日韩高清网页| 天天摸夜夜添逼| 亚洲av大片在线播放| 抓住我的双乳咬我奶头视频看| 色多多成人黄在线观看| 最好看的最新高清中文字幕7| 国产av在哪里看| 亚洲av成人在线影院| 人妻少妇偷人精品视频片段| 丰满高跟丝袜老熟女HD| bt天堂新版中文在线| 亚洲少妇zo另类| 欧美午夜性春交| 国产精品一区二区三区黄| POPNHUB国产在线观看| 欧美日韩成人伦理电影| 久久久久久亚洲一区| 亚洲欧美日韩在线二区| 日韩精品中文字幕在线视频 | 日韩一级午夜影院| 亚洲精品中文字幕乱码3| 欧美性色xxⅹxx毛片| 久久久久人妻精品乱码| 亚洲加勒比少妇无码AV| 亚洲午夜禁在线观看| 成人免费视频www| 久久成人免费电影| 高潮爽死痉挛白浆喷水np小说| 韩国乱码伦视频免费| 色爱区综合激月婷婷激情| 黄岩帕菲克精品主题酒店| 久久haose精品| 16女下面流水不遮视频| 女人被弄到呻吟的视频| 岛国激情视频一区二区三区| 人妻精品未满十八少妇精品| 亚洲欧美二区绝色浪潮性色| 久久98精品国产亚洲av| 亚洲国产成人精品女人久久久久| 日本电影中文字幕一区久久久久久久看 | 欧美精品第六区| 亚洲精品a久久久久| 亚洲高清大片| 禁止的爱善良的未删减版在线播放 | 18美女裸免费观看网站| 国内精品视频自在欧美一区| 99久久综合免费| 国产美女被强在线观看| 九色成人免费视频| 亚洲免费av天堂| 日韩一区二区三区影院| 初学生裸体洗澡自拍视频| 新不卡在线播放av| 国产嫩草影院入口九色| 欧美日韩精品久| 精品视频在线观看中文字幕 | 区二区三区国产精华液| 人妻少妇久久久久久97人妻二| 免费视频爱爱太爽了网站| 熟女人妻少妇久久久久久| 久久伊人精品影院一本到综合 | 杨幂脱了内裤让男生桶视频| 欧美亚洲精品激情中文字幕| 日韩午夜影片| 伊人青青大草原| 欧美成人一二区| 夜夜夜夜夜久久久久| 久久成年免费电影| 极品av高潮| 大又大粗又爽又黄少妇毛片口| 躁天天躁中文字幕在线| 色播五月六月丁香| 国产成人1卡2卡3卡4卡| 卡美歌干白葡萄酒价格 | 好男人视频在线观看一区| 久久久久人人人人人| 高清亚洲va| 色狠狠久久AV北条麻妃| 欧美精品一区二区,| 一本久久综合精品| 亚洲成人av高清在线观看| 97人妻人人～碰人人爽| 九一蜜桃视频在线观看| 暖暖直播在线观看免费韩国| 99久久久久精品影院| v电影v亚洲v欧美v国产| 一本久久综合精品| 日本高清视频色视频免费| 六十熟妇乱子伦视频| 欧美成人一级免费高清| 又黄又硬又粗又长又爽的视频| 精品卡一卡二卡三卡四视频版| 岛国av一区二区三区久久精品| 97久久久国产精品消防器材优势| 喷潮娇喘喷水呻吟高潮夜夜嗨| 狠狠婷婷综合久久久久久88av| 99久久首页| 亚洲专区精品在线| 看黄色片子一级片| 在线ww观看www网站| 人妻精品久久一区二区三区| 国产三级美女视频| 适合在在自慰时看的黄文| 精品偷自拍另类在| 久久午夜精品福利一区二区| 扒开女人两片毛茸茸黑森林| 国产一区二区欧美日韩精品| 嫩草影院网站进入| 2019久久久高清日本道| 亚洲日本不卡| 成人av 网站在线观看| 国产熟女欧美一区二区| 国产免费的又黄又爽又色视频| 欧美乱大交xxx春色| 国产精品一区激情电影| 日本a√视频在线| 特级毛卡片普通话不收费| 国产亚洲日韩一区二区三区| 免费午夜爱爱视频| 国产麻豆成人精品免费网站| 人妻三级日本香港三级极97| 精品国产乱码久久久久久站| 朝鲜少妇漂亮毛茸茸| 欧美日韩a级毛片| 国产毛片精品一区二区在线 | 一区二区三区四区激情视频| 最新在线精品国产福利| 少妇免费观看视频| 啊啊啊一区二区三区在线观看| 寂寞影院一区二区三区| 欧美色视频免费| 装不下已经流出来了好烫| 亚洲一区二区色| 老女人一级毛片| 国内精品一区国产vr| 无遮挡18禁啪啪网站| 久久精品国产91久久麻豆| 18禁无遮挡在线网站| 中国人与黑人牲交FREE欧美| 黄色软件免费下载观看| 18男同志GAY亚洲| 久久国产乱子伦50精品欧美| 二区播放日韩欧美| 日韩免费播放一级毛片| 国内精品久久久久久蜜桃| 人妻人妻人人澡人人爽| 久久亚洲第一区| 美女18毛片a级毛片视频| 秋霞一级黄色大片| 女人和男人啪视频在线观看 | 18禁羞羞视频无遮挡免费| 男女无遮挡免费网站观看| 亚洲七久久之综合七久久| 亚洲av曰韩精品久久久久久| 欧美日韩一区二区精品视频| avaaa亚洲国产一区| 精品国产美女久久av| 亚洲av日韩av网| 国产免费又黄又爽又刺激软件| 欧美激情视频免费一区二区三区| 男人天堂大片| 国产成人精品久久久久网址| 好男人在线观看视频在线观看 | 国产高清啪免费视频| 永久免费AV无码网站04| 女人被躁到高潮嗷嗷叫费观 | 扒开双腿猛进入爽爽免费视频| 青青草视频在线免费观看| 欧美日韩精品一区二区性色| 白嫩少妇私密保健按摩| 在线天堂最新中文网| 日韩欧美不卡视频一区二区三区| 久久精品人人妻人人爽| 侵犯洗澡女教师在线观看| 一二三四在线中文视频| 久久精品免费看国产免费| 7777中文字幕| 久久久一精品| 国产av全部| 波多野结衣人妻中出| 在线人成免费视频69国产| 国产乱人偷精品视频| 18XXXX中国学生| 成年人床上av片免费观看网| 制服诱惑av一区二区| 午夜久久久久| 午夜影院在线观看国产精品| 国产精品久久77777av| 亚洲国产一区二区三区网站| 免费成人三级黄色片| 国产精品毛片av一区二区三对| 欧美日韩激情另类| 老熟女久久久| 国产成人无码免费视频97| 久久久久久免费观看全是精品| 男人裸体自慰免费看网站| 亚洲,自偷,自拍网| 国产成人精品一区91| 操出白浆网址| av毛片在线观看地址| 18女人小正毛片| 老司机免费成人影院| AV第一福利在线导航| 综合九色综合欧美狠狠|| 日本欧美国产区一区| 国产亚洲自在精品一区| 含羞草实验室入口网站免费进| 小sao货大ji拨cao死你| 亚洲欧美日韩综合三区| 116美女写真| 欧美日韩av视频一区| 乱人伦精品在线观看| 国产精品区久久久| 国产一区二区精品免费| 黄床大片免费观看| 美女内射精品一级片tv| 精品国产一区二区av麻豆不卡| 亚洲精选一区二区在线观看| 豪妇荡乳1一5潘金莲| 日韩欧美精品一区二区三区经典| 欧美性猛交ⅹxxx乱大交少妇| 亚洲妇女自偷自偷图片| 大香蕉av在线| 国产一区二区成人精品| 日日尻夜夜爽| 天天一区二区日本电影三级| A片试看120分钟做受视频大全| av在线天堂最新版| 欧美亚洲一区二区三区精品| 成人在线午夜免费视频| 日日操,夜夜骑| 九七人妻碰碰视频| 一个人www在线视频| 久久99久久观看吃奶视频| FREEXXXXHD国语对白| 精麻豆亚洲av国产品∵美女| 最近最新2019中文字幕6| 国产麻豆剧传媒精品国产av蜜桃| 国产欧美日韩一区二区精品| 在线看国产精品三级在线| 亚洲美女丝袜制服av| 久久久午夜精品福利| 人人爱人人做人人干| 久久99精品无毒不卡| 精品亚洲av乱码国产毛片| 漂亮女医生被强奷在线观看| 午夜福利福利视频| 久久精品黄色免费小视频| XFPLAY无码中文AV资源站| 免费一级做a爰片久久毛片无遮挡| 日韩一二三区视频免费观看| 国产美女上床网站| 久久精品都在这里| 蜜桃av免费网站| 浙江老熟女露脸| 国产一级片男人天堂| 免费高清成人黄色视频在线观看 | 乱人伦精品在线观看| 夫妻真的交换| 精品一区二区三区四区五区乱码| 看黑人巨大精品欧美一区二| 国产999精品黄片| 亚洲九九香蕉| 欧美91激情亚洲| 成人影院麻豆视频| 日本一本二本三区高清资源 | av网站在线观看亚洲| 人人妻人人爽欧美| 一级看片免费视频精品| 男女一边摸一边做爽爽的免费 | 国产美女免费视频| 亚洲熟妇丰满大| 国产最爽男女视频| 免费久久一级黄片| 亚洲国产成人资源在线观看| 可以在线免费观看黄色视频的网站| 国产一区二区制服诱惑| 午夜久久久久影院| 做床爱免费视频在线观看| 亚洲怡红院日本| 国产久久精品久久| 人妻卧室迎合领导进入| 调教乳头的黄色视频| 最近2019中文字幕高清免费视频 | 五十六十日本老熟妇一乱| 我的公强要了我高潮中文字幕| 欧美aaaaa级黑人又粗又长| 国产精品视频免费观看| 好爽~~~~嗯~~~再快点视频| 欧美老熟妇乱人伦人妻| 国产精品一区二区精品视频观看| 乌克兰少妇性疯狂| av无码av在线a∨天堂| 欧美性极品少妇精品网站| 亚洲av午夜福利精品| 女人的超长巨茎人妖在线视频| 日本免费视频色www| 亚洲免费精品aⅴ国产| 亚洲欧洲日产中文高清| 成年女性特黄午夜视频免费看| 国产欧美一区日韩| 91中文嫩草影院| 久久久亚洲熟妇熟女ⅹxxx毛片| WWXXXXX日本高潮| 日韩a级福利视频| 日韩午夜国产| 午夜伦理一区二区视频| 黑色丝袜老师好紧我要进去了 | 很黄的视频久久| 亚洲精品国产成人99久久6小说| 四虎永久在线精品视频| 女人十六女人十六毛片| 日韩午夜国产| 久久午夜精品电影| 亚洲一区成人av片在线观看| 啪啪啪高潮喷水视频| 精品国产亚洲一区观看| 久久大香蕉精品视频| 欧美视频亚洲精品| 黄上黄床高清大全在线免费看| 色天天天天爽夜夜| 日韩乱人伦视频| 国产精品激情在线播放| mm1314亚洲国产精品| 欧美亚洲一区中文字幕亚洲| 欧美日韩av久久久| 日本三级黄色视频| 国产国内久久精彩国语对白视频| 迷人的保姆在线观看| 欧美亚洲精品一区二区色| 亚洲国产成人精品女人久久久久| 国产激情一区二区三区3d| 蜜桃av麻豆一区中文字幕| 真人试看做受120秒3分钟| 亚洲中文字幕精品久久久久久| 国产精品久久久久69孕妇9| 久久久久久国产精品免费精品| 亚洲男人天堂999| 大学生久久香蕉国产线看观看| xxx日本一二三区不卡| 色婷婷久久久亚洲欧美| 人妻熟女av久久| 国产精品亚洲精品欧美精品| 黄免费视频大全| 宅男午夜福利视频在线观看| 日日碰狠狠躁久久躁| 久久久亚洲av国产精品| 亚洲另类国产欧美一区二区| 精品少妇人妻av免费久久| 又色又爽又黄的三级视频3d| 免费观看精品久久| 免费的黄色视频国产| 亚洲精品国产成人av| 毛片在线观看黄| 女人被躁到高潮嗷嗷叫免费| 国产无遮挡无码视频在线观看 | 亚洲欧美v日韩色国产v| 色男噜噜噜亚洲男人| 被男子脱掉内裤的美女视频| 国产精品一区二区国产激情久久| 国产精品一区二区av国| 无码熟妇人妻AV在线影片 | xoxoxo性ⅹyy欧美| 国产精品人妻一区一区三区 | 日韩人妻系列一区二区三区| 欧美精品色一区二区三区| 国产精品一区探花| 一级做a爰片久久免费观看 | 欧美日韩在线精品成人| 亚洲精品日韩系列在线| 宅男午夜激情一区二区免费播放| 欧美日韩高清有码| 久久黄色一级视频免费试看片国产精品一区二区色就是 | 国产成人色在线视频| 岳好紧好紧我要进去了视频| 男女做爰猛烈叫床吃奶视频| 成a人片国产精品| 永久免费福利网站| 国产一区二区三区不卡免费视频| 日韩欧美国产免费观看| 久久精品免费看国产免费| 香蕉91在线精品国产亚洲| 色噜噜狠狠一区二区三区四区偷拍| 裸体美女扒开尿口视频| 国产精品三级经典| 欧美小呦精品在线| 欧美一区二区三黑人| 国产视频内射| 51久久成人国产精品| 精品中文字幕专区| 99re在线观看视频免费| 黄色av网站中文字幕| 日本高清乱理伦片中文字幕| 美女黄网站18禁免费看夜情| 美女张开腿让男人桶到爽裸体| 日韩亚洲欧美熟女网站| 成人精品99| 久久精品这就是精品| 最近最新高清中文字幕大全免费8| 舔吸到高潮视频| 欧美国产精品一级二级三级| 亚洲精品国产美女久久久久久| 美女高潮流白浆在线免费观看| 自拍偷区色综合| 日本免费一区二区三区激情视频| 国产成人欧美一区二区| A毛片免费全部播放完整| 夫妻真的交换| 人人爽人人爽人人爽人人片av| 欧美最猛性xxxxx亚洲精品| 国产精品视频播放不卡| 日韩av免费网站| 黄片av91| 又色又激情的免费视频| 不卡一级黄色视频| 想看黄色特级毛片| 99亚洲一区二区三区在线观看| avi亚洲码中文字幕一区二区| 欧洲极品诱惑另类视频| 成人国产色综合| 国产一级内射老妇| 国产国模影院午夜一区| 亚洲精品在线va| 中文免费女人观看在线毛片| 午夜福利午夜福利a| 久久精品亚洲精品国产区美| 国产精品自在线拍观看| 少妇被粗大物体猛烈进出| 热99re久久精品国产一区二区| 中文字幕精品人妻熟女在线| 黄色免费网站免费看| 在线久久av| 亚洲综合av在线| 亚洲日韩高清在线亚洲专区| 欧美综合在线激情专区| 亚洲加勒比少妇无码AV| BT在线WWW网在线| 正在播放流白浆| 日本最新色视频在线观看| 麻豆AV无码精品一区二区| 中文字幕熟女av| 极品人妻被内射中出| 福利国产一区二区三区| 久久这里只有精品re9| 国产av一区二区三区麻豆| 被黑人猛躁10次高潮视频| 国产亚洲欧洲一区二区| 欧美日韩福利视频一区二区| 2020国产精品视频观看| 欧美成人三级短视频| 成人高清国产在线观看| 女人毛片免费观看| 久久国产成人网| 一区二区三区免费久久| 亚洲av色图天堂在线| 永久免费AV无码网站04| 午夜福利免费在线观看欧美成人| 上了漂亮少妇视频在线观看| 秋霞在线观看日韩av| 大又大粗又爽又黄少妇欧美毛片| 色爱区综合激月婷婷激情| 久久精品免视看国产成人| 怡红院影院亚洲| 美女被强,射一奶子| av制服丝袜诱惑天堂| 亚洲66av| 日日干夜夜夜了| AV潮喷大喷水系列无免费| tobu8在线观看免费直播| 国产午夜视频性色| 国产L精品国产亚洲区| 精品三级在专区精品国产| 99人妻人人| 欧美性猛交╳xxx乱大交人| 欧美视频观亚洲| 女人十八水多毛片免费看| 在线成av人网站| 欧美午夜精品一二三区91电影| 把少妇弄高潮了WWW| 亚洲色偷偷综合亚洲av伊人| 风韵丰满人妻熟妇老熟女啪啪| av网站国产日韩| 久久久国产18精品久久久久不卡| 欧美成年人精品性视频| 亚洲一区二区三区av黄片| 99人妻人人| 成人欧美亚洲综合| 人禽杂交18禁网站| 绯色av一本一道道久久精品| 蜜月98久久综合国产精品一区| 国产成人精品三级麻豆| 国产成人精品久久二区二区91| 亚洲国产av韩国乱线| 女人18毛片水真多免费观| 国产午夜精品电影网| 在线天堂WWW在线资源| ZOZOZO女人与牛交全过程| 91av看片在线| 久久久久精品国产片毛片| 白带异常呈黄色| av在线毛片播放| 黄片a在线播放| 苍井そら无码AV| 成人午夜影院在线免费观看| 国产精品免费人成网站| 久久青草综合色| 91亚洲观看在线欧美亚洲| 精品人妻无吗一区二区三区四区| 亚洲在线中文字幕| 亚洲色无码播放亚洲成AV| 五月婷婷丁香综合在线观看| 精品国产一区二区三区不卡| 欧美18性xxxx18性欧美| 国产欧美精品亚洲日本一区| 免费看黄色av网址| 熟女人妻无乱码中文字幕| 亚洲怡红院日本| 最新av免费| 免费无毒永久av网站| 999精品视频免费看| 欧洲免费无线码在线观看| 日韩毛片av天码| 一区二区国产成人精品| 国产av一区二区久久久久| 亚洲激情欧美另类| 新生儿为什么边吃奶边哭| 我和亲妺作爱妺妺下面好湿| 新婚少妇无套内谢国语播放| 久久99国产热| 热久久精品推荐| 亚洲一区二区三区av无| 性夜影院爽黄A爽免费看| 国产亚洲精品欧洲在线| 欧美九一精品久久久熟妇人妻| 最好看的2019中文无字幕| 免费观看欧美色视频| 边摸边脱边吃奶边做视频| 在线观看av不卡| 极品videossex| 97久久热精品| 亚洲+欧洲+日产+韩国精品| 狼友网精品视频在线观看| 国产亚洲精品网站在线视频| 国产精品天天影视久久综合| 国产综合亚洲精品一区二区三区| 岛国av高清不卡免费| 日韩精品国产高清在线观看| 一级a一级a爰片免费久久久| 国产美女午夜福利久久| 日韩国产欧美在线播放| 波多野结衣在线精品视频| 亚洲性无码AV在线DVD| 亚洲国产精品免费进入观看| 免费看黄a级毛片下载| 日本av视频观看| 日本的黄色视频网站免费| 亚洲丰满熟妇哎xxxⅹ色| 久久国产精品99久久| 亚洲国产日韩欧美高清不卡| 中国老女人XXHD| 别揉我奶头嗯啊叫的视频| 欧美激情日韩另类综合一区| 日韩精品v欧美精品v亚洲 | 亚洲男人天堂中文字幕| 久久伊人毛片av| 成人av精品麻豆| H无码精品动漫在线观看免费| 激情亚洲欧美激情| 秋霞电影网久久久| 岛国av高清不卡免费| 精品999久视频在线| 亚洲国产精品亚洲一区二区三区| 啪啪免费福利午夜| 人妻少妇福利视频| 久久99九九99九九精品| 欧美一区二区成人综合| 毛片高清免费视频| 日本乱理伦片在线观看真人|